FUTABA 01000141 Скачать руководство пользователя страница 75

Страница: 75 / 225

System Type selection

The T16IZ is for 2.4 GHz only. The system can

be changed from among 6 choices: FASSTest

18CH, FASSTest12CH, FASST MULTI, FASST

7CH, T-FHSS, S-FHSS. It is FASSTest18CH and

FASSTest12CH which can be chosen by R7108SB

set. The method of selection is on the next page.

*If you change the System type, other model data is not reset.
*After any change, remember to test the model and fully

check servo direction and motion.

*Analog servos cannot be used with the R7108SB in the

FASSTest12CH mode.

System type

System mode setting, Receiver link

Receiver linking

The receiver will only be controlled (without being

affected by other transmitters) by the transmitter it

is linked to. When using a receiver other than one

purchased as a set, linking is necessary.

Moreover, a re-link is required when a new model

is added by model selection, and at the time of

system type change.

Dual receiver function (only FASSTest 18CH )

Dual receivers can be linked with the T16IZ.

Two receivers are recognized individually by ID

numbers. For example, in R7108SB, CH output

setting function is used, by setting the first as as

"1-8CH", and setting the second as "9-16CH".

Two sets of receivers can be used as a set in the

model, allowing you 16 channels. Separate fail-safe

voltage can be set to each receiver.

However, telemetry cannot be used for the 2nd

receiver.

Battery fail-safe voltage setup (FASSTest /T-FHSS

mode only)

The voltage at which battery fail-safe activates can

be set when you link. (3.5-8.4 V) The receiver

memorizes the setting as it was at link.

Since power consumption varies with battery type,

servos and condition, please select the fail-safe

activation voltage for your own model.

● Select [System type] in the Linkage menu

and access the setup screen shown below.

P.39

Linking method

Cases when linking is necessary:

・

When using a receiver other than the initial setting.

・

When the communication system was changed.

(FASSTest18CH

↔

FASSTest12CH etc.

)

・

When a new model was created by model

selection.

Telemetry function (FASSTest /T-FHSS mode only)

To use the telemetry function, set “Telemetry” to

“ACT”.

DL Interval (FASSTest mode only)

When a telemetry function is enabled, the receiving

interval (down-link interval) of sensor data can be

changed.

If a DL interval is increased, the response of the

sensor data display becomes slower, but stick

response will improve.

●Return to

Linkage

*FASST MULTI/FASST 7CH cannot be selected for Europe.

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды