manualshive.com logo in svg

FUTABA 01000141, Полное руководство

FUTABA 01000141 - полная инструкция пользователя для скачивания бесплатно. Подробный мануал содержит все необходимые сведения о продукте. Скачайте его с manualshive.com прямо сейчас и ознакомьтесь со всеми функциями и возможностями этого устройства.

Поделиться
Скачать
background image

179

S.BUS Basic Menu

S.BUS Basic Menu

The channel of each function 

can be changed.

This resets the S.BUS channel assign-
ments back to the defaults.

The 

"

SBUS BASIC

"

 screen is accessed via the 

"

BASIC MENU

"

 screen. Set the CH for each function according to the transmitter to be used. 

Any unused functions should be set to INH (Inhibited).  For example, if the Gain A/E and Gain RUD remote gain functions are not going to 

be used, then set them to [INH].  The CGY760R/CGY755 will then allow you to make gain adjustments within the respective menu.

WARNING 

 

  Always verify that the S.BUS function as-

signments match your transmitter’s function 
(in the FUNCTION menu) assignments.  If any 
changes are made within the transmitter func-
tion assignments, then it will also be neces-
sary to make the changes within the S.BUS 
function assignments.  To change the channel, 
CGY and T16IZ must be connected.

ELE2 channel Servo Type  

(If you want to use the ELE2 port for purposes other than swash.)

This selects the ELE2 servo types.  There are three types of the servo 
driving frequency selection, AN:70

 

Hz, DG285 Hz, and 760 μS.  All Futaba 

digital servos can be operated with fastest DG:285 Hz mode but some 
of other brands of servos do not support DG:285 Hz mode.  In this case, 
select the proper servo driving frequency per the manufacturer’s specifi-
cations. 
If you select H4-00 or H4-45 with 4 servo swashes, cannot set this ELE2 
port servo type. In that case, select all swash servo types in SWH basic 
servo type.

Setting: AN:70 Hz / DG:760 μS / DG:285 Hz

　

Initial setting: DG:285 Hz

WARNING 

 The servo type parameter within the CGY must match the type of 

servo you are using.  Incorrect setting may damage the CGY or the 
servo.  Incorrect setting may also result in a loss of control during 
flight.

 S. BUS connection: Condition on change channel   

Using the methodology described previously, determine the  "Cond CH #" and 
set the condition change channel of the transmitter.  In this example, DG1 is the 
conditional change channel.

As with the flight condition function of the transmitter, it is possible to utilize 
pre-determined settings, each activated by a switch or switches on the 
transmitter.  By setting the condition switch on the channel with the AFR 
function of the transmitter and setting the point for each flight condition with 
the AFR point curve, you can switch the condition of CGY760R/CGY755 in 
conjunction with the flight condition switch of the transmitter.

Wireless channel     

The wireless channel uses two consecutive channels.  For example, if CH13 
is set to "# 1", CH14 is automatically set to "# 2". Therefore, when using this 
function, two consecutive free channels are required for the transmitter.  It is not 
possible to use a channel assign that is used for another function. 

CAUTION

 Be sure to check the operation for all conditions 1 to 5 before flying.
 The setting of "wireless CH" is possible only when the transmitter 

and the CGY are powered off and the CGY is turned on.

 Be sure to connect and disconnect the CGY and T16IZ connection cable 

with the power off.

2 consecutive free channels

Содержание 01000141


































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 01000141

ABB REC650 ANSI Applications Manual preview
REC650 ANSI
Бренд: ABB Страницы: 370
ABB EAN823 Instructions Manual preview
EAN823
Бренд: ABB Страницы: 17
ABB COM600 series User Manual preview
COM600 series
Бренд: ABB Страницы: 104
ABB AC 800M Library Object Style Manual preview
AC 800M
Бренд: ABB Страницы: 120
ABB ABILITY SSC600 Product Manual preview
ABILITY SSC600
Бренд: ABB Страницы: 42
CAME Z Series Instruction Manual preview
Z Series
Бренд: CAME Страницы: 12
CAME Z Series Technical Documentation Manual preview
Z Series
Бренд: CAME Страницы: 16
Ultrak KEGS5000 User Manual preview
KEGS5000
Бренд: Ultrak Страницы: 41
Zander Aachen ZX Series Quick Start Manual preview
ZX Series
Бренд: Zander Aachen Страницы: 10
Eaton SC100 Operation Handbook preview
SC100
Бренд: Eaton Страницы: 86
MADRIX AURA Technical Manual & Quick Start Manual preview
AURA
Бренд: MADRIX Страницы: 36
Accel 300+ Installation Instructions Manual preview
300+
Бренд: Accel Страницы: 8
Paradox Grafica DNE-K07 Reference And Installation Manual preview
Grafica DNE-K07
Бренд: Paradox Страницы: 24
Panosol SR658 Operation Manuals preview
SR658
Бренд: Panosol Страницы: 105
Pangolin FB4 Series Quick Start Manual preview
FB4 Series
Бренд: Pangolin Страницы: 8
WAREMA LONMSE 2M230I Operating And Installation Instructions preview
LONMSE 2M230I
Бренд: WAREMA Страницы: 4
Xilinx Virtex-6 FPGA Hardware Setup Manual preview
Virtex-6 FPGA
Бренд: Xilinx Страницы: 2
Parker TFP Series Operation Manual preview
TFP Series
Бренд: Parker Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды