manualshive.com logo in svg

FUTABA 01000141, Полное руководство

FUTABA 01000141 - полная инструкция пользователя для скачивания бесплатно. Подробный мануал содержит все необходимые сведения о продукте. Скачайте его с manualshive.com прямо сейчас и ознакомьтесь со всеми функциями и возможностями этого устройства.

Поделиться
Скачать
background image

196

Swash Detail

Swash Detail

The swash detail setting is used to keep the swash plate level at high and low collective pitch to cyclic interactions and cyclic 

pitch to collective pitch interactions. 

"

Swash Detail

"

 screen from the 

"

EXPERT MENU 3D

"

 screen.

(1) PIT AIL: collective pitch   aileron mixing rate             

Going from MID to HIGH and MID to LOW collective pitch check that the 
swash plate is traveling flat throughout the entire range.

[Setting method]

 Operate the transmitter stick in the direction you want to 

set. Touch the button lit in green to enter the setting mode and adjust the 
mixing rate. Do the same for the other side.

Setting ranges:  30 ~ 150%     Initial value: 100%

(2) PIT ELE: collective pitch   elevator mixing rate             

Going from MID to HIGH and MID to LOW collective pitch check that the 
swash plate is traveling flat throughout the entire range.

[Setting method]

 Operate the transmitter stick in the direction you want to 

set. Touch the button lit in green to enter the setting mode and adjust the 
mixing rate. Do the same for the other side.

Setting ranges:  30 ~ 150%     Initial value: 100%

(3) PIT ELE2: collective pitch  2nd  elevator  mixing  rate           

This parameter adjusts the pitch to 2nd elevator mixing rate.  The rates can 
both be adjusted individually for both full high and low collective positions.  

Note: 

This setting is only available if the 

H4-xx swash mode

 has been 

selected.

Setting ranges:  30 ~ 150%     Initial value: 100%

(4) AIL PIT: aileron collective pitch mixing rate             

At the middle collective pitch, check that during right to left and left to right 
aileron action the swash plate is staying level on both the elevator and col-
lective pitch axis.  If the swash plate is rising or falling with aileron inputs.

[Setting method]

 Operate the transmitter stick in the direction you want to 

set. Touch the button lit in green to enter the setting mode and adjust the 
mixing rate. Do the same for the other side.

Setting ranges:  30 ~ 150%     Initial value: 100%

(5) AIL ELE: aileron  elevator mixing rate           

This parameter adjusts the aileron to elevator mixing rate.  The rate can be 
adjusted for left and right directions individually.  

Note: 

This setting is only 

available if the 

H4-45 swash mode

 has been selected.

Setting ranges:  30 ~ 150%     Initial value: 100%

(6) AIL ELE2: aileron  2nd elevator mixing rate           

This parameter adjusts the aileron to 2nd elevator mixing rate.  The rate 
can be adjusted for left and right directions individually.  

Note: 

This setting 

is only available if the 

H4-45 swash mode

 has been selected.

Setting ranges:  30 ~ 150%     Initial value: 100%

Содержание 01000141


































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 01000141

Aalborg DPC Operating Manual preview
DPC
Бренд: Aalborg Страницы: 128
Panasonic FP7 Series Additional Functions Manual preview
FP7 Series
Бренд: Panasonic Страницы: 45
Magnescale MG10-P1 Instruction Manual preview
MG10-P1
Бренд: Magnescale Страницы: 132
VADDIO EVI-D70 Installation And User Manual preview
EVI-D70
Бренд: VADDIO Страницы: 2
Lawler 61 Series Installation & Maintenance Manual preview
61 Series
Бренд: Lawler Страницы: 4
Hama 11412 Operating Instruction preview
11412
Бренд: Hama Страницы: 46
Galcon 61 Series Installation And Operating Instructions Manual preview
61 Series
Бренд: Galcon Страницы: 35
Jands SafeGuard Installation Manual preview
SafeGuard
Бренд: Jands Страницы: 7
hager coviva Smartbox TKP100A Operation And Configuration Instructions preview
coviva Smartbox TKP100A
Бренд: hager Страницы: 34
Samson FOUNDATION 3730-5 Mounting And Operating Instructions preview
FOUNDATION 3730-5
Бренд: Samson Страницы: 132
Samson 3767 Mounting And Operating Instructions preview
3767
Бренд: Samson Страницы: 68
Samson 3730-2 Mounting And Operating Instructions preview
3730-2
Бренд: Samson Страницы: 128
Samson 3725 series Mounting And Operating Instructions preview
3725 series
Бренд: Samson Страницы: 68
X-POWER MULTI 1 Instruction And Installation Manual preview
MULTI 1
Бренд: X-POWER Страницы: 24
Samson TROVIS 3730-1 Mounting And Operating Instructions preview
TROVIS 3730-1
Бренд: Samson Страницы: 80
Haehne DCX Quick Start Manual preview
DCX
Бренд: Haehne Страницы: 44
Samwontech TEMP2000 Series Installation Manual preview
TEMP2000 Series
Бренд: Samwontech Страницы: 91
Warren rupp HDF3-A Original Instructions Manual preview
HDF3-A
Бренд: Warren rupp Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды