manualshive.com logo in svg

FUTABA 01000141, Полное руководство

FUTABA 01000141 - полная инструкция пользователя для скачивания бесплатно. Подробный мануал содержит все необходимые сведения о продукте. Скачайте его с manualshive.com прямо сейчас и ознакомьтесь со всеми функциями и возможностями этого устройства.

Поделиться
Скачать
background image

103

Telemetry : GPS [Distance]

Displaying data from the Distance Screen

The Distance screen displays and sets altitude data 

from an SBS-01/02G GPS Sensor (sold separately), 

and allows the distance to the airborne aircraft to 

be read by the transmitter. When the aircraft flies 

inside or outside the set distance, an alarm and 

vibration alerts the pilot.

*The GPS sensor is necessary, and is sold separately. Mount 

and  connect  the  sensor  in  accordance  with  the  sensor 

instruction manual. 

*A GPS sensor must be installed in the aircraft.

Sets the distance 

on which the alarm 

operates. 

● Tap the [GPS] button in the Telemetry screen to call 

the setup screen shown below.

Max. and min. values 

s i n c e   t h e   p o w e r 

was turned ON will 

display.

*It cannot be used in FASST mode and S-FHSS mode.

*Only receiver voltage and EXT voltage can be used in 

FASSTest12CH mode.

*The FASSTest18CH /T-FHSS mode can use all the telemetry 

functions.

Distance

Alarm is chosen from 

Buzzer, Voice, and 

Inhibit.

Allows Speech to be 

turned ON or OFF.

↑ An upward arrow 

indicates the alarm 

will sound when the 

d i s t a n c e   r e a c h e s 

above your set value.

↓ A downward arrow 

indicates the alarm 

will sound when the 

d i s t a n c e   r e a c h e s 

below your set value.

Tap to the [Preset] of "Reference" 

item. Sets the current aircraft position 

as the starting point.

Surface

Altitude

Slant

Altitude calculated as either straight line distance 

(slant) or surface distance on a map can also be 

selected.

Select <Slant> <Surface>  to "Distance mode", tap the 

screen.

Type 1

Type 2

Type 3

"Vibrator" type

If the following types are selected, the transmitter 

will vibrate during the warning.

●Return to 

Linkage menu

Содержание 01000141


































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 01000141

zipwake S Series Troubleshooting Manual preview
S Series
Бренд: zipwake Страницы: 12
Watts 7 Series Installation, Maintenance & Repair preview
7 Series
Бренд: Watts Страницы: 2
jbc UCR Instruction Manual preview
UCR
Бренд: jbc Страницы: 12
FATEK FBs-1HLC Operation Manuals preview
FBs-1HLC
Бренд: FATEK Страницы: 10
RAKwireless RAK3172 User Manual preview
RAK3172
Бренд: RAKwireless Страницы: 6
Ultratec SureFire Operation Manual preview
SureFire
Бренд: Ultratec Страницы: 33
ULTIMATE SPEED ULG 17 A1 Operation And Safety Notes preview
ULG 17 A1
Бренд: ULTIMATE SPEED Страницы: 97
DMX4ALL ArtNet-DMX Mux16 User Manual preview
ArtNet-DMX Mux16
Бренд: DMX4ALL Страницы: 21
Data Signs PTL Compact 2 Operation And Maintenance Manual preview
PTL Compact 2
Бренд: Data Signs Страницы: 23
Seneca Z-PC SERIES Installation Manual preview
Z-PC SERIES
Бренд: Seneca Страницы: 4
Z-Wave Z-URC 550EU Operating Instructions Manual preview
Z-URC 550EU
Бренд: Z-Wave Страницы: 44
Powers HydroGuard 1430 Series Quick Start Manual preview
HydroGuard 1430 Series
Бренд: Powers Страницы: 8
Parallax Ag9050 Quick Start Manual preview
Ag9050
Бренд: Parallax Страницы: 3
Water Specialist WS1CC Operation And Instruction Manual preview
WS1CC
Бренд: Water Specialist Страницы: 60
aerl CoolMax SRX Installation And Operation User Manual preview
CoolMax SRX
Бренд: aerl Страницы: 27
FUTABA FP-5NLH Instruction Manual preview
FP-5NLH
Бренд: FUTABA Страницы: 6
VeriFone Commander Site Controller Software Installation Manual preview
Commander Site Controller
Бренд: VeriFone Страницы: 34
Eaton Cutler-Hammer S701X25N3BP Instruction Leaflet preview
Cutler-Hammer S701X25N3BP
Бренд: Eaton Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды