FUTABA 01000141 Скачать руководство пользователя страница 9

Страница: 9 / 225

Never disassemble or modify the SD card.

Do not bend, drop, scratch or place heavy objects on

the SD card.

If smoke or an abnormal odor emanates from the card,

immediately turn off the transmitter power.

Since the SD card is an electronic device, be careful of

static electricity.　

■ Static electricity may cause erroneous operation or other

trouble.

Do not use the SD card near radio and television sets,

audio equipment, motors and other equipment that

generates noise.　

■ Doing so may cause erroneous operation.

Do not store the SD card in the following places:

・ Where the humidity is high

・ Where the temperature difference is severe

・ Where it is very dusty

・ Where the card will be exposed to shock and vibration

・ Near speakers and other magnetic devices

micro SD Card (Commercial Product) Handling Precautions

WARNING

CAUTION

*Read the instruction manual supplied with the SD card for details.

● Recorded data

The data recorded on the SD card cannot

be compensated regardless of the contents

or cause of the trouble or obstruction.

Futaba does not perform data restoration

or recovery work.

Do not use the SD card where it may be exposed to

water, chemicals, oil, or other fluids.　

■ Doing so may cause a fire or electric shock by short circuiting.

Do not insert foreign matter into the transmitter card slot.

■ Doing so may cause erroneous operation.

Do not expose the card to shock and vibration and do

not remove the card from the card slot while data is be-

ing written or read.　

■ The data may be damaged or lost.

Keep wireless equipment, batteries, aircraft, etc.

away from children.　

Do not directly expose plastic parts to fuel, oil, ex-

haust gas, etc.　

■ If left in such an environment, the plastic may be damaged.
■ Since the metal parts of the case may corrode, always keep

them clean.

Join the Academy of Model Aeronautics.　

■ The Academy of Model Aeronautics (AMA) provides guidelines

and liability protection should the need arise.

Storage and Disposal Precautions

Other Precautions

WARNING

CAUTION

Do not store wireless devices in the following places:

・ Where it is extremely hot (40℃ [104 ℉ ] or higher) or

cold (-10℃ [14 ℉ ] or lower)

・ Where the equipment will be exposed to direct sun-

light

・ Where the humidity is high

・ Where vibration is prevalent

・ Where it is very dusty

・ Where the device may be exposed to steam and heat

CAUTION

When the device will not be used for a long time, re-

move the batteries from the transmitter and aircraft and

store them in a dry place where the temperature is be-

tween 0℃ and 25℃ [32 ℉ and 77 ℉ ].

■ Leaving batteries inside your model and radio when they are not

being used for long periods will result in battery deterioration,

liquid leakage and other damage.

Always use genuine Futaba products such as trans-

mitter, receiver, servo, ESC, etc.

■ Futaba is not responsible for damage sustained by combination

with parts other than Futaba Genuine Parts. Use the parts
specified in the instruction manual and catalog.

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды