FUTABA 01000141 Скачать руководство пользователя страница 128

Страница: 128 / 225

128

AIL

AIL 3

(Chip Aileron)

AIL 4

(Chip Aileron)

AIL1

(Main Aileron)

AIL 2

(Main Aileron)

FLP 2

(Camber Flap)

FLP 1

(Camber Flap)

AIL → Camber flap

[Corresponding model type]: Airplane/

glider, 2 ai 2 flaps or more

This mix operates the camber flaps (FLP1/2)

in the aileron mode. When the aileron stick

is manipulated, the ailerons and camber flaps

perform aileron operation simultaneously and

the operation characteristic of the roll axis is

improved.

● The aileron left/right mixing rate of each flap servo

can be fine-tuned.

● A mixing curve can be set.

● An ON/OFF switch can be set.

● Linking is possible: Link this mix to other mixes.

Adjustment of each

flap servo

Setting method

● Tap [INH].

(ON is displayed.)

● When setting a switch, tap the [--] item of

the switch and tap the screen to call the

selection screen, and then select the switch

and set its ON direction. (Always ON at "--"

setting)

(For a description of the switch selection

method, see the the back of this manual.)

● Tap the left or right item of each flap servo.

Adjust the mixing rate.

*When the mixing direction is reversed by the linkage,

adjustments can be made by changing the mixing rate

polarity (+ or -).

● A mixing curve can be set. (1/2 page)

(For a description of the mixing curve setting

method, see the description at the back of

this manual.)

● To set linking, tap the [Link] item.

Set it to ON and tap the screen.

● Select [AIL→Camber flap] at the

model menu and call the setup

screen shown below.

Currently selected condition name

● Mixing curve setting

(For a description of the

setting method, see the

description at the back

of this manual.)

Left/right overall

adjustment at Rate A

and Rate B

Activate the function by

tapping the [INH].

Condition group/single

mode selection (Gr. /Sngl)

The ON/OFF switch of

mixing is chosen.

To set linking, tap to

the [OFF] item

●Return to Model menu

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды