FUTABA 01000141 Скачать руководство пользователя страница 97

Страница: 97 / 225

Altitude

Sets the altitude

on which the alarm

operates.

↑ An upward arrow

indicates the alarm

will sound when the

altitude reaches above

your set value.

↓ A downward arrow

indicates the alarm

will sound when the

altitude reaches below

your set value.

Alarm is chosen from

Buzzer, Voice, and

Inhibit.

Allows Speech to be

turned ON or OFF.

Allows Melody to be

turned ON or OFF.

● Tap the [Altitude] button in the Telemetry screen to

call the setup screen shown below.

Max. and min. values

s i n c e t h e p o w e r

was turned ON will

display.

*It cannot be used in FASST mode and S-FHSS mode.

*Only receiver voltage and EXT voltage can be used in

FASSTest12CH mode.

*The FASSTest18CH /T-FHSS mode can use all the telemetry

functions.

Type 1

Type 2

Type 3

"Vibrator" type

If the following types are selected, the transmitter

will vibrate during the warning.

Telemetry : Altitude

Displaying data from the altitude

Altitude is a screen which displays / sets up the altitude

information from an optional altitude sensor or GPS sensor.

The altitude of the model which is flying can be known. If it

becomes higher (low) than preset altitude, you can be told by

alarm. Warning by vibration can also be chosen. Data when

a power supply is turned on shall be 0 m, and it displays the

altitude which changed from there. Even if the altitude of an

airfield is high, that shall be 0 m and the altitude difference

from an airfield is displayed. This sensor calculates the

altitude from atmospheric pressure. Atmospheric pressure

will get lower as you go up in altitude. Using this, the

sensor will estimate the altitude. Please understand that an

exact advanced display cannot be performed if atmospheric

pressure changes in a weather situation.

First, the set of a reference is required.

1. The model and transmitter to which the

altitude sensor was connected are turned on.

2. Tap to the [Preset] of "Reference" item.

*Atmospheric pressure is changed according to the weather

also at the same airfield. You should preset before a flight.

Alarm set : Altitude

1. Tap Alarm and choose from Buzzer, Voice,

and Inhibit.

2. Choose "Inhibit" for Vibrator if no

using the

vibrator alarm. If using vibrator, choose one

of the three types.

3. Tap to the Limit [xxx

] item .

4. Adjust the rate using the "▼▼" "▼" "▲" "▲▲"

buttons.

Initial value: ↑200 m ↓-50 m

Adjustment range -500 m~+3,000 m

(↑Limit

≧

↓Limit)

*When the screen is tapped for one second, the rate is reset

to the initial value.

5. To terminate the input and return to the

original state, push the HOME/EXIT button.

*An altitude sensor or GPS sensor must be installed in the aircraft.

● If this is set to Mode1-4,

a rise and dive are told

by a different melody.
Mode1: Little rise/dive

→ Melody changes

: sensitively

Mode4: Big rise/dive

→ Melody changes

: insensible

●Return to

Linkage menu

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды