FUTABA 01000141 Скачать руководство пользователя страница 215

Страница: 215 / 225

215

Switch selection method

The various functions used in the T16IZ can be selected by switch. The switch (including when stick, trim

lever, or VR are used as a switch) setting method is common to all functions.

Switch selection

When a switch is selected at a mixing function, etc., the selection screen shown below is called.

(Switch selection screen example)

When switch is selected

Switch ON/OFF setting is possible at each position.

1. When the ON/OFF "Set" position switch is

tapped after the switch was selected, the

screen shown below appears.

*When the button of each position is tapped,

it toggles between ON and OFF.

2. Tap the button and set to the ON position.
3. Close the screen by tapping [Hardware

select].

When stick, trim lever, or VR is

selected.

When a stick, trim lever, or VR is used as a switch,

the following 4 modes can be selected.

Tap the chosen

switch.

Normal or Alternate: Alternate switching

mode is available depending on mixing

function.

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды