FUTABA 01000141 Скачать руководство пользователя страница 83

Страница: 83 / 225

Tapping this will change

INH to ON and activated.

Stick alarm　

An alarm (single beep) can be sounded at the

specified throttle stick position.

●Alarm function ON/OFF can be set by switch.

Tapping this will pull up the hardware selection

screen. Select the switch and ON-OFF direction if

turning the function ON-OFF by switch.

This is the current

position display bar for

the throttle stick.

This is the throttle stick

alarm position. Push the

throttle stick to the desired

position and tap the value.
Range:

（Low）0 ～ 100（High）

If the throttle stick

reaches the yellow

line, an alarm will

sound.

If the throttle stick

reaches the desired

position , an alarm

(single beep) will

sound.

●Return to Linkage menu

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды