FUTABA 01000141 Скачать руководство пользователя страница 85

Страница: 85 / 225

INT (integration) Timer is the function which changes progress of a timer according to the location

of the throttle stick. When the throttle stick is raised for faster speed, the speed of the timer usually

increases. With the throttle stick at mid-range speed, the timer speed decreases (to 50%). When the

throttle is positioned at low end, the timer's progress stops. It's possible to set it in the time which

fits power consumption of your fuselage.

*The consumption of the battery/fuel is different depending on the conditions, so use an INT Timer as

reference.

*The INT (integration) time is different from the actual elapsed time.

High

Middle

Low

When a throttle stick is the

high side, the speed of the

timer usually increases.

When a throttle stick is

middle-speed, the timer

speed decreases (by 50%).

When a throttle stick is low,

timer progress stops.

Nomal Timer

TH% :

Integration Timer

● Select [Timer] at the linkage menu and call the setup

screen shown below.

Tap

INT time (%)

INT Time

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды