FUTABA 01000141 Скачать руководство пользователя страница 114

Страница: 114 / 225

114

When using at the teacher side

1. Select the mode.

*When changing the mode, tap to the item you want to

change and change the mode using the "▼▼" "▼" "▲"

"▲▲" buttons. The display blinks. Tap the screen to change

the mode.

"Teacher/Student": Select [Teacher].
"ACT/INH": Enable operation by changing to

[OFF] or [ON].

"16/12/8 CHANNEL": When the student uses

the T16IZ (including the T18MZ, T32MZ, T14SG)

select [16CH]. Otherwise select [12CH]

or[8CH].

2. Select the trainer switch.

*When setting or changing the switch, tap to the "SWITCH"

item, call the switch setup screen and set the desired switch

and ON/OFF direction.

(See "Switch selection method" at the end of this

manual for selection method details.)

*The switch mode can also be selected when setting the

ON position on the switch setup screen. When [Normal] is

selected, normal ON/OFF operation is performed. When

[Alternate] is selected, the trainer function is alternately

turned on and off each time the switch is operated. This

allows alternate ON/OFF switching even when a momentary

switch (SH) is used.

Note: The trainer function won’t be turned

on unless the Instructor's transmitter receives

signals from the student's transmitter. Be

sure to confirm this after connecting your

trainer cable.

When using at the student side

1. Select the mode.

*When changing the mode, tap to the item you want to

change and change the mode using the "▼▼" "▼" "▲"

"▲▲" buttons. The display blinks. Tap the screen to change

the mode.

"Teacher/Student": Select [Student].
"ACT/INH": Enable operation by changing to

[ACT].

"16/12/8 CH": When the student uses the

T16IZ, T14SG, T18SZ, T16SZ, T18MZ, T32MZ select

[16CH]. When the student uses the T14MZ,

T12Z, T12FG or FX-40, select [12CH]. Otherwise

select [8CH].

Note: In "student mode", only the teacher

side can turn on and off the power to the

student's transmitter. Keep the power switch

always at off position.

● Tap the [Trainer] button in the Linkage menu to call

the setup screen shown below.

●Return to Linkage menu

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды