manualshive.com logo in svg

FUTABA 01000141, Полное руководство

FUTABA 01000141 - полная инструкция пользователя для скачивания бесплатно. Подробный мануал содержит все необходимые сведения о продукте. Скачайте его с manualshive.com прямо сейчас и ознакомьтесь со всеми функциями и возможностями этого устройства.

Поделиться
Скачать
background image

187

Rudder Basic

Rudder Basic

In the 

"

Rudder Basic

"

 menu, you make the basic setting of the rudder gyro. 

"

Rudder Basic

"

 screen from the 

"

BASIC MENU

"

 screen.

WARNING 

 Do not connect the tail rotor servo to the gyro until the 

servo type has been selected.  Operating the servo using the 
incorrect setting may damage the CGY or the servo.

 Do not operate with the linkage connected until the "Srv. 

Limit" function correctly sets the servo limit point.  If the 
servo operates beyond the linkage operating range, there is a 
danger of either the servo or helicopter being damaged.

WARNING 

  The servo type parameter within the CGY must 

match the type of servo you are using. Incorrect 

settings may damage the CGY or the servo. An 

incorrect setting may also result in a loss of control 

during flight.

(1) Servo Type 

Select the appropriate setting for the tail rotor servo.

Setting: Analog / DG:1520 / DG760

Initial setting: DG:1520

DG 1520: BLS254, BLS257, S9254, S9257

DG 760: BLS276SV, BLS251SB, BLS251, S9256, S9251

(2) Gyro. Dir: Gyro direction         

This parameter controls which direction the CGY (yaw axis) will compen-
sate when the helicopter rotates.  Hold the tail rotor linkage over the link-
age ball on the servo, pick the helicopter up by the main shaft and rotate 
the mechanics counter-clockwise.  The CGY should compensate by adding 
clockwise rotation pitch to the tail rotor blades.  If the CGY compensates by 
adding counter-clockwise rotation pitch to the tail rotor blades, then it will 
be necessary to reverse the Compensation Direction setting by pressing 
the "Gyro Dir".

Setting value:  Normal / Reverse     Initial value: Normal

(3) Work Mode: Gyro working mode         

The available choices are CMT, Normal or AVCS. The CMT mode will allow 
you to select either AVCS or Normal mode via the transmitter.  In Normal 
mode the gyro will always operate in Normal Rate Mode, and when AVCS 
is selected, it will always operate in AVCS Mode.

Setting: CMT / Normal / AVCS     Initial setting: CMT

(4) GY. Gain: Gyro base gain setting         

This parameter sets the base gain of the gyro.  This can be used to adjust 
the gain % if your actual transmitter gain does not match the gain on the 
CGY correctly.

Setting ranges: 0 ~ 150%    Initial value: 100%

(5) Srv. Limit: Limit setting         

When the CGY is in the "Srv.Limit" parameter mode, the gyro will no lon-
ger operate and the tail servo will always center when the tail rotor stick 
is released.  Always exit the setup functions before attempting to fly the 
model.  Before each flight, always ensure that the gyros are operating and 
compensating in the correct direction.  The Servo Limit parameter within 
the CGY is used to set the mechanical limits for the tail rotor servo.  To 
obtain the best performance it is recommended to set the limit in the CGY 
to 100% for both directions and then adjust the servo arm length to set the 
mechanical endpoints.  After that has been completed, use the servo limit 
parameter to make small adjustments that could not be made mechani-
cally.  Values between 90% and 110% are considered optimal. 

[ Setting method ]

Operate the rudder stick right or left in the direction you want to set. Touch 
the button that is lit in green to set the limit. Do the same for the other side.

WARNING 

 When using the CGY for the first time, or when making mechani-

cal changes involving throw, you must check and set the servo limits 
again to prevent binding.

Содержание 01000141


































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 01000141

NCR 1651 Quick Reference Manual preview
1651
Бренд: NCR Страницы: 6
Rain Bird IQ Installation & User Manual preview
IQ
Бренд: Rain Bird Страницы: 48
Gardner Denver AirSmart G2 Installation Manual preview
AirSmart G2
Бренд: Gardner Denver Страницы: 22
B&G NMEA 2000 Installation Manual preview
NMEA 2000
Бренд: B&G Страницы: 2
Hanna Instruments HI 8001 Instruction Manual preview
HI 8001
Бренд: Hanna Instruments Страницы: 88
K9Safety K9Caller Configuration Manual preview
K9Caller
Бренд: K9Safety Страницы: 9
Eaton S701 Instruction Leaflet preview
S701
Бренд: Eaton Страницы: 8
Pando PI3300 Instructions For Use Manual preview
PI3300
Бренд: Pando Страницы: 43
Union Instruments CWD2005 SPC Operating Instructions And Safety Notes preview
CWD2005 SPC
Бренд: Union Instruments Страницы: 63
Zeta Premier MX-16 Installation And Commissioning Manual preview
Premier MX-16
Бренд: Zeta Страницы: 44
Ultraflex B47 Installation Instructions Manual preview
B47
Бренд: Ultraflex Страницы: 7
Jäger ADwin HSM-24V Manual preview
ADwin HSM-24V
Бренд: Jäger Страницы: 18
FUTABA FP-4NBF Instruction Manual preview
FP-4NBF
Бренд: FUTABA Страницы: 8
HomeMatic HmIP-FAL230-C10 Installation And Operaion Manual preview
HmIP-FAL230-C10
Бренд: HomeMatic Страницы: 42
Carrier AQUASNAP 30RA "B" Operation & Maintenance Instructions Manual preview
AQUASNAP 30RA "B"
Бренд: Carrier Страницы: 36
Joy-it Moto1 Quick Start Manual preview
Moto1
Бренд: Joy-it Страницы: 7
Woodward Vertex-Pro Installation/Hardware Manual preview
Vertex-Pro
Бренд: Woodward Страницы: 112
Anritsu MU120119A Operation Manual preview
MU120119A
Бренд: Anritsu Страницы: 54

Бренды по названию

Популярные бренды

Загрузить еще бренды