manualshive.com logo in svg

FUTABA 01000141, Полное руководство

FUTABA 01000141 - полная инструкция пользователя для скачивания бесплатно. Подробный мануал содержит все необходимые сведения о продукте. Скачайте его с manualshive.com прямо сейчас и ознакомьтесь со всеми функциями и возможностями этого устройства.

Поделиться
Скачать
background image

57

Battery 

 Low battery alarm voltage set 

*When the low battery voltage setting is changed, it is changed for 

every model in the transmitter. A unique voltage cannot be set for 

each model.  A change in the low battery voltage setting also does 

not reset other data. 

Select the battery alarm voltage according to the 

battery to be used.

Battery type change : 

Lipo(2cells) → Manual 

setting

It isn't indicated in case 

of manual setting.

Vibrator Types

Type 1

Type 2

Type 3

Auto power off time setting

T h i s   f u n c t i o n   p r e v e n t s   b a t t e r y 

discharging if the transmitter power 

supply does not erase. 
1. Adjust the auto power off time with 

the value input buttons.

*When the time the transmitter is inactive reaches  

the set time, the power is turned off automatically. 

This time can be set up to 1 hour in 10 minutes 

increments. The auto power off function can also 

be deactivated.

*An audible alarm is sounded from 3 minutes 

before auto power off. When a stick or switch is 

operated, the alarm is cleared.

 

Refer to P.42

Range Check

Before a flight ground range check.

The 'range check mode' reduces the transmission 

range of the radio waves to allow for a ground 

range check.

*The range check mode, when activated, will continue for 

60 seconds unless the user exits this mode early. When the 

progress bar reaches 60 second mark, the RF transmission 

automatically

 

returns to the normal operating power.

WARNING

Do not fly in the range check 

mode.  

*Since the range of the radio waves is 

short, if the model is too far from the 

transmitter, control will be lost and the 

model will crash.

●Return to System menu

When choosing manual 

setting, the numerical 

value can be input.

It's dangerous to 

set it manually in 

the low voltage.

Содержание 01000141


































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 01000141

ABB REC650 ANSI Applications Manual preview
REC650 ANSI
Бренд: ABB Страницы: 370
ABB EAN823 Instructions Manual preview
EAN823
Бренд: ABB Страницы: 17
ABB COM600 series User Manual preview
COM600 series
Бренд: ABB Страницы: 104
ABB AC 800M Library Object Style Manual preview
AC 800M
Бренд: ABB Страницы: 120
ABB ABILITY SSC600 Product Manual preview
ABILITY SSC600
Бренд: ABB Страницы: 42
Radio Shack 4 Owner'S Manual preview
4
Бренд: Radio Shack Страницы: 52
Parasound 7100 Owner'S Manual preview
7100
Бренд: Parasound Страницы: 72
Jafar 7010 Operation And Maintenance Manual preview
7010
Бренд: Jafar Страницы: 15
B&R Industries AP1000 User Manual preview
AP1000
Бренд: B&R Industries Страницы: 89
GBD BA100 Instructions For Installations preview
BA100
Бренд: GBD Страницы: 68
Bartec MAK 3003 Manual preview
MAK 3003
Бренд: Bartec Страницы: 26
V2 CU1 Manual preview
CU1
Бренд: V2 Страницы: 48
National Instruments SCC-DO01 User Manual preview
SCC-DO01
Бренд: National Instruments Страницы: 14
Kampmann 197901960988 Manual preview
197901960988
Бренд: Kampmann Страницы: 5
K&K M3500N Installation Instructions Manual preview
M3500N
Бренд: K&K Страницы: 10
Xylem LOWARA Aquavara IPC Quick Start Manual preview
LOWARA Aquavara IPC
Бренд: Xylem Страницы: 292
Gimenez Ganga Saxun Mosquito Screen Lateral Door 2020 Assembly Manual preview
Saxun Mosquito Screen Lateral Door 2020
Бренд: Gimenez Ganga Страницы: 2
Keysight Technologies J-BERT M8020A Installation Manual preview
J-BERT M8020A
Бренд: Keysight Technologies Страницы: 78

Бренды по названию

Популярные бренды

Загрузить еще бренды