FUTABA 01000141 Скачать руководство пользователя страница 113

Страница: 113 / 225

113

Trainer

Trainer system starting and setting

T16IZ trainer system makes it possible for the

instructor to choose which channels and operation

modes can be used in the student's transmitter.

The function and rate of each channel can be set.

The training method can also be matched to the

student's skill level. Two transmitters must be

connected by an optional Trainer Cord, and the

Instructor's transmitter should be programmed for

trainer operation, as described below.

When the Instructor activates the trainer switch, the

student has control of the aircraft (if MIX/ FUNC/

NORM mode is turned on, the Instructor can make

corrections while the student has control). When

the switch is released the Instructor regains control.

This is very useful if the student gets the aircraft

into an undesirable situation.

● Setting data are stored to model data.
● Student rate can be adjusted at MIX/FUNC/

NORM mode.

● Activated student channels can be selected

by switches.

Note:

This trainer system can be used in the following

manner:

1. With the T16IZ transmitter and a conventional

transmitter, if the channel order is different, it is

necessary to match the channel order before using this

function.

You can select the channel of input data from student's

transmitter in the "FUNC" or "MIX" mode.

2. When the T16IZ is used as the instructor’s transmitter,

set the modulation mode of the student’s transmitter to

PPM.

If being used as the student, T16IZ can be connected to

the instructor's transmitter which requires the student's

mode to be PPM. T16IZ always sends PPM mode signal

from the trainer jack.

(In the case of student's transmitters other than 2.4 GHz)
3. Be sure that all channels work correctly in both

transmitters before flying.

Corresponding types of transmitters and trainer mode settings:

Types of transmitters

Instructor's transmitter settings

Student's transmitter settings

System Type

Trainer setting

System Type

Trainer setting

Trainer Cords

Instructor

Student

Mod. mode

CH mode

Mod. mode

CH mode

Mod. mode

T16IZ,FX-32

T14SG,T16SZ,

T18SZ,T18MZ,

T32MZ

T16IZ,FX-32

T14SG,T16SZ,

T18SZ,T18MZ,

T32MZ

Arbitrary

16CH

Arbitrary

16CH

T12FG and 9C

Trainer Cords

T16IZ

T14MZ, FX-40, T12Z,

T12FG,

FX-30

Arbitrary

12CH

PCM-G3

2.4G

12CH

PPM

T16IZ

T8FG, FX-20

Arbitrary

12CH

FASST-MLT2

8CH

FASST-MULT

T16IZ

T10C, T9C,

T7C,T6EX, T4EX

Arbitrary

8CH

PPM

T12FG

T16IZ

T10CG,T7C

Arbitrary

8CH

Arbitrary

T12FG

T16IZ

T10J, T8J, T6K, T6J,

T6L

Arbitrary

8CH

Arbitrary

T12FG and 9C

Trainer Cords

T14MZ, FX-40, T12Z,

T12FG,

FX-30

T16IZ

Arbitrary

12CH

Arbitrary

12CH

T8FG, FX-20

T16IZ

Arbitrary

12CH

Arbitrary

12CH

T10C, T10CG, T10J,

T9C, T7C

T7C, T8J, T6K

T6J

T16IZ

Arbitrary

8CH

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды