manualshive.com logo in svg

Daikin RXYQ5PY1, Руководство по обслуживанию

На нашем сайте вы можете скачать бесплатно сервисный мануал для Daikin RXYQ5PY1. Этот руководство поможет вам правильно обслуживать и настраивать ваш кондиционер. Скачайте его сейчас с manualshive.com и получите подробные инструкции по эксплуатации вашего устройства.

Поделиться
Скачать
background image

Installation

SiEN34-705

54

General Information

Caution:

•

Drain piping connections
Do not connect the drain piping directly to sewage pipes that smell of ammonia. The 
ammonia in the sewage might enter the indoor unit through the drain pipes and corrode the 
heat exchanger.

•

Keep in mind that it will become the cause of getting drain pipe blocked it water collects on 
drain pipe.

3PA60996-14Y

TEST

WHEN ELECTRIC WIRING WORK IS FINISHED 

 

Check drainage flow during COOL running, explained under ‘‘TEST OPERATION’’.

WHEN ELECTRIC WIRING WORK IS NOT FINISHED 

 

Remove the terminal box lid connect a power supply and remote control to the terminals.

(Refer to the Installation Manual) 

Next, press the inspection/test operation button “ 

” on the remote control. The unit will engage the 

test operation mode. Press the operation mode selector button “ 

” until selecting FAN OPERATION 

“ 

”. Then, press the ON/OFF button “ 

”. The indoor unit fan and drain pump will start up. Check 

that the water has brained from the unit. Press “ 

” to go back to the first mode.

 

 

Note that the fan also starts rotating. 

Attach the terminal box lid as before.

TEST

≥?

100

Fig. 24

R(L) S(N)

T2

T1

F2

F1

P2

P1

REMOTE

CONTRL

TRANSMISSION

WIRING

FORCED

OFF

Fig. 25

(Tube should be 
about 100 mm long.)

Plastic watering can

Service drain outlet (with rubber plug)

(Use this outlet to drain water from  
the drain pan)

<Adding water through air discharge outlet>  
 

[Method of adding water]

Drain pipe

Remote control 
wiring

Remote control 
wiring

Power supply wiring

Power supply 
terminal board

Terminal board for 
remote control

Power supply wiring

Terminal box lid

(2) 

After piping work is finished, check if drainage flows smoothly.

 

Add approximately 2 liter of water slowly from the air outlet and check drainage flow.

Содержание RXYQ5PY1




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RXYQ5PY1

Salamander Pumps EVE Installation And Warranty Manual preview
EVE
Бренд: Salamander Pumps Страницы: 24
Daewoo HEA1139 Manual preview
HEA1139
Бренд: Daewoo Страницы: 9
Jackco 842 Instruction preview
842
Бренд: Jackco Страницы: 8
S&P SAHARA Series Installation Manual. Instructions For Use preview
SAHARA Series
Бренд: S&P Страницы: 18
Underhill GULP PRO Care And Maintenance Instructions preview
GULP PRO
Бренд: Underhill Страницы: 2
Airtecnics SMART ECG 1000 A Installation, Operation And Maintenance Manual preview
SMART ECG 1000 A
Бренд: Airtecnics Страницы: 22
T.I.P. HWA 6000 EPF Manual preview
HWA 6000 EPF
Бренд: T.I.P. Страницы: 84
Superior Radiant EW30L48 Installation, Operation And Service Instructions preview
EW30L48
Бренд: Superior Radiant Страницы: 12
pyromaster UVHB20 Homeowner'S Installation And Operating Manual preview
UVHB20
Бренд: pyromaster Страницы: 16
Consort PHSL2 Series Installation & Control Manual preview
PHSL2 Series
Бренд: Consort Страницы: 4
Eagle Pro EPB Series Instruction Manual preview
EPB Series
Бренд: Eagle Pro Страницы: 50
York YCUL0020 Installation, Operation And Maintenance Manual preview
YCUL0020
Бренд: York Страницы: 178
evoheat Evo Flex Installation & Operation Manual preview
Evo Flex
Бренд: evoheat Страницы: 17
Midea MCCU-03CN1A Installation Manual preview
MCCU-03CN1A
Бренд: Midea Страницы: 13
AMAZON COMMERCIAL B07SRXJF1W Manual preview
B07SRXJF1W
Бренд: AMAZON COMMERCIAL Страницы: 48
Marta MT-CH2453A User Manual preview
MT-CH2453A
Бренд: Marta Страницы: 12
Giant LP122A Series Operating Instructions/ Repair And Service Manual preview
LP122A Series
Бренд: Giant Страницы: 12
Daikin EWAA008D2V3P-H Installation Manual preview
EWAA008D2V3P-H
Бренд: Daikin Страницы: 44

Бренды по названию

Популярные бренды

Загрузить еще бренды