manualshive.com logo in svg

Daikin RXYQ5PY1, Руководство по обслуживанию

На нашем сайте вы можете скачать бесплатно сервисный мануал для Daikin RXYQ5PY1. Этот руководство поможет вам правильно обслуживать и настраивать ваш кондиционер. Скачайте его сейчас с manualshive.com и получите подробные инструкции по эксплуатации вашего устройства.

Поделиться
Скачать
background image

Operation Manual

SiEN34-705

326

Operation Manual

Note

•

The heating capacity drops as the outside temperature 
falls. If this happens, use another heating device together 
with the unit. (When using the appliances which produce 
open fire together, ventilate a room constantly.)
Do not place appliances which produce open fire in places 
exposed to the air flow from the unit or under the unit.

•

It takes some time for the room to warm up from the time 
the unit is started since the unit uses a hot-air circulatory 
system to warm the entire room.

•

If the hot air rises to the ceiling, leaving the area above the 
floor cold, we recommend using the circulator (the indoor 
fan for circulating air). Contact your dealer for details.

2-6-2 Program Dry Operation

•

The function of this operation is to decrease the humidity in 
your room with a minimum temperature decrease.

•

The micro computer automatically determines temperature 
and fan speed.

•

The system does not go into operation if the room temper-
ature is low.

•

The microcomputer automatically controls the temperature 
and fan speed, so these cannot be set using the remote 
control.

•

This function is not available if the room temperature is 
20°C or lower.

FOR SYSTEMS WITHOUT COOL/HEAT SELECTOR (Refer to 
figure 5)

Press the operation mode selector button several times and 
select “

” ( program dry operation).

Press the on/off button.
The operation lamp lights up and the system starts operation.
Press the air flow direction adjust button (only for FXC, FXF, 
FXH, FXK, FXA). Refer to the chapter “Adjusting the Air Flow 
Direction” for details.
Press the on/off button once again.
The operation lamp goes off and the system stops operation.

Note

•

Do not turn off the power immediately after the unit stops.

•

The system need at least 5 minutes for residual operation 
of drain pump device.
Turning off the power immediately will cause water leak or 
trouble.

FOR SYSTEMS WITH COOL/HEAT SELECTOR (Refer to figure 8)

Select cooling operation mode with the Cool/Heat selector.
Press the operation mode selector button several times and 
select program dry “

”.

Press the on/off button.
The operation lamp lights up and the system starts operation.
Press the air flow direction adjust button (only for FXC, FXF, 
FXH, FXK, FXA). Refer to the chapter “Adjusting the Air Flow 
Direction” for details.
Press the on/off button once again.
The operation lamp goes off and the system stops operation.

Note

•

Do not turn off the power immediately after the unit stops.

•

The system need at least 5 minutes for residual operation 
of drain pump device.
Turning off the power immediately will cause water leak or 
trouble.

2-6-3 Adjusting the Air Flow Direction

(Refer to figure 6) (only for FXC, FXF, FXH, FXK, FXA)

Press the air flow direction button to select the air 
direction.
The air flow flap display swings as shown right 
and the air flow direction continuously varies. 
(Automatic swing setting)
Press the air flow direction adjust button to select 
the air direction of your choice.

The air flow flap display stops swinging and the 

air flow direction is fixed. (Fixed air flow direction 
setting)

figure 5

1

2

3

4

figure 8.1

figure 8

1

2

3

4

5

figure 6

1

2

Содержание RXYQ5PY1




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RXYQ5PY1

iGenix IG9010 Instructions For Use Manual preview
IG9010
Бренд: iGenix Страницы: 6
VEAB EA Series Fitting Instructions Manual preview
EA Series
Бренд: VEAB Страницы: 16
Salda EKS User Manual preview
EKS
Бренд: Salda Страницы: 12
Gardner Denver Elmo Rietschle V-VC 40 Original Operating Instructions preview
Elmo Rietschle V-VC 40
Бренд: Gardner Denver Страницы: 32
Raider RD-EFH02 User Manual preview
RD-EFH02
Бренд: Raider Страницы: 54
HeatStar HSRR30SP(LP) Operating Instructions And Owner'S Manual preview
HSRR30SP(LP)
Бренд: HeatStar Страницы: 32
Wacker Neuson PT 6L Operator'S Manual preview
PT 6L
Бренд: Wacker Neuson Страницы: 72
Chiltrix V18-B Installation And Operation Manual preview
V18-B
Бренд: Chiltrix Страницы: 19
CTC Union EcoAir 115 Exchange Instruction preview
EcoAir 115
Бренд: CTC Union Страницы: 2
NewAir AH-600 Owner'S Manual preview
AH-600
Бренд: NewAir Страницы: 11
Zoeller Basement Sentry 507 Installation Manual preview
Basement Sentry 507
Бренд: Zoeller Страницы: 8
Goldair GOC177C General Care And Safety Manual preview
GOC177C
Бренд: Goldair Страницы: 8
Pentair Jung Pumpen 35/2 M Instruction Manual preview
35/2 M
Бренд: Pentair Jung Pumpen Страницы: 26
Okay RFP 5200 Translation Of The Original Instructions preview
RFP 5200
Бренд: Okay Страницы: 52
Noctua NF-B9 PWM User Manual preview
NF-B9 PWM
Бренд: Noctua Страницы: 2
Thermix KPH 1300-B Installation & User Manual preview
KPH 1300-B
Бренд: Thermix Страницы: 4
Pressol Polypropylene Rotary Drum Pump Operating Instructions & Parts Manual preview
Polypropylene Rotary Drum Pump
Бренд: Pressol Страницы: 3
fluid-o-tech DGD PRO Series Instruction Manual preview
DGD PRO Series
Бренд: fluid-o-tech Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды