Daikin RXYQ5PY1 Скачать руководство пользователя страница 151

Страница: 151 / 355

SiEN34-705

Appendix

General Information

145

7.9 Outdoor Unit Multi Connection Piping Kit

7.9.1 BHFP22P100 · 151

This kit contains the following parts.

<Do not throw away any of the accessories until installation is complete>

Component parts

Kit

name

BHFP

P100

BHFP

P151

Caution

•

Please be sure to read this manual before installation and follow the instruction carefully when performing installation work.

•

See the outdoor unit’s installation manual for outdoor unit installation.

•

Installation of interconnecting piping between the outdoor units, REFNET joint or REFNET header will be needed separately

Gas-side joint

Liquid-side joint

Gas-side reducer

Liquid-side reducer

insulating

tube for

gas pipe

insulating

tube for

liquid pipe

Big

Small

Shape

Number of outdoor units connected
Outdoor unit Multi Connection Piping Kit

Selection Procedure

2 units

BHFP22P100

3 units

BHFP22P151

•

2 or 3 outdoor units can be connected.

• There are restrictions on the combination and the installation order of outdoor units,

so please refer to “the Engineering Data of VRV III” and “the installation manual”
(attached sheet of outdoor unit) for details.

The following parts are needed to connect
this kit and are not included

Field supply parts

Selection Procedure

See the “Connecting Pipe Sizes and location of cutting the joint” for

details on the necessary size.

Prepare a gas pipe diameter for the upper outdoor unit as listed in

“Connecting Pipe Sieze and location of cutting the joint.”

For insulation materials

Q’ty

Name

Insulation for piping
Connection piping

Elbow

Tape

1set

1pc

1set

Field supply parts

•

Quantity and selection procedure of elbow only applies to a front or bottom connection.

•

For a lower front connection the quantity and selection procedure are different, so please refer to the instructions for

a lower front connection.

•

A joint for the same diameter pipes is needed only for a bottom connection.

See the instructions for the bottom connection, for details on quantity and specifications.

•

The min. thickness of the pipes in this manual shows the requirements of Japanese High Pressure Gas Control low.

(As of Jan. 2003)

•

And the temper grade (O,1/2H) shows the material type of JIS h 3300. The tickness and material shall be selected in

accordance with local for the design pressure 4.OMPa (40bar).

(Unit : mm)

Caution

Temper grade

Copper tube O.D.
Copper tube W.T.

(Minimum requirement

O Type

1/2H Type

6.4

0.80

15.9

0.99

9.5

0.80

12.7

0.80

22.2

0.80

19.1

0.80

25.4

0.88

28.6

0.99

31.8

1.10

34.9

1.21

41.3

1.43

38.1

1.31

Содержание RXYQ5PY1




































































































































































































































































































































































Результаты поиска

Содержание RXYQ5PY1

Отзывы:

Похожие инструкции для RXYQ5PY1

Бренды по названию

Популярные бренды

Daikin RXYQ5PY1, Руководство по обслуживанию

Результаты поиска

Содержание RXYQ5PY1

Отзывы:

Похожие инструкции для RXYQ5PY1

Бренды по названию

Популярные бренды