Daikin RXYQ5PY1 Скачать руководство пользователя страница 126

Страница: 126 / 355

Test Operation

SiEN34-705

120

General Information

Detailed Setting
Procedure of Low
Noise Operation
and Demand
Control

1. Setting mode 1 (H1P off)

In setting mode 2, push the BS1 (MODE button) one time.

→

Setting mode 1 is entered and

H1P off.
During the setting mode 1 is displayed, “In low noise operation” and “In demand control” are
displayed.

2. Setting mode 2 (H1P on)

In setting 1, push and hold the BS1 (MODE button) for more than 5 seconds.

→

Setting

mode 2 is entered and H1P lights.

Push the BS2 (SET button) several times and match the LED display with the Setting No.
you want.

Push the BS3 (RETURN button) one time, and the present setting content is displayed.

→

Push the BS2 (SET button) several times and match the LED display with the setting

content (as shown below) you want.

(

Push the BS3 (RETURN button) two times.

→

Returns to

)

Push the BS1 (MODE button) one time.

→

Returns to the setting mode 1 and turns H1P off.

Содержание RXYQ5PY1




































































































































































































































































































































































Результаты поиска

Содержание RXYQ5PY1

Отзывы:

Похожие инструкции для RXYQ5PY1

Бренды по названию

Популярные бренды

Daikin RXYQ5PY1, Руководство по обслуживанию

Результаты поиска

Содержание RXYQ5PY1

Отзывы:

Похожие инструкции для RXYQ5PY1

Бренды по названию

Популярные бренды