Daikin RXYQ5PY1 Скачать руководство пользователя страница 159 | Manualshive

Страница: 159 / 355

background image

SiEN34-705

Appendix

General Information

153

2-2 Connection of pipes

CAUTION

• Remove the knockout plate on the bottom frame. (See the installation manual attached to the outdoor unit)
• Connect the gas and liquid pipe as shown in the figure below. (When connecting the pipes, first connect the gas-side joint and the gas-side

reducer (1), the liquid-side joint and the liquid-side reducer (1)).

• See the caution section in the installation manual attached to the outdoor unit for brazing pipes and connecting pipes with flare nuts.
• Install the joint in such a way that the attached face of the caution label becomes horizontal. (See the view A)
• Connect the liquid side reducer (1) tilting approx. 10° and bend the field supplied liquid pipe up to the stop valve as shown in the figure below.

(See the view A)

• If the liquid side reducer is connected vertically without bending the liquid pipes, the insulation will not fit.

(Attached to the outdoor unit)
Liquid-side accessory pipe assy (1)

(Attached to the outdoor unit)
Gas-side accessory pipe assy (3)

Gas-side reducer (1)

Gas-side reducer (3)

Liquid-side
reducer (1)

Gas-side joint

Liquid-side joint

Liquid pipe
(field supply)

Liquid pipe
(field supply)

Gas pipe (field supply)

(select the pipe length on site)

straight size joint
(field supply)

straight size joint
(field supply)

Outdoor

unit A

Outdoor

unit B

Elbow
(field supply)

Gas pipe 2
(field supply)
(As per Table 4)

Gas pipe 2
(field supply)
(As per Table 5)

Liquid-side reducer

Gas-side joint

Liquid-side joint

Ground

Max.
+ 15°

Max.
+ 15°

View

(10°)

The work after the kit is connected

Connection of piping between the outdoor unit and the indoor unit

Air tight test

Insulation of joints

(1) Fit the insulation to the reducer and temporarily keep it in place with tape.
(2) Cut insulating tube along the slit. (See the figure at the right.)

Fit the insulation to the joint and temporarily keep it in place with tape without leaving a
gap between the insulation mating faces.

(3) Seal the seam between the insulation and the field supply piping insulation with the

field supply tape.

(4) Wrap the tape around the insulation attached to the joint without leaving a gap.

(

section shown in the figure at the right.)

Follow the instructions in the installation manual included with the outdoor unit,
when performing installation work.

Insulating tube

Tape (field supply)

Reducer

Insulating tube

Cut along the slit

Joint

Tape (field supply)

Tape (field supply)

Tape (field supply)

Local pipe’s insulating material

(1)

(2)

(3)

(4)

«
...
157
158
159
160
161
...
»

Содержание RXYQ5PY1




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RXYQ5PY1

Бренд: NARVI Страницы: 48

Бренд: Warmco Страницы: 25

Бренд: Cantherm Страницы: 11

MPXI11MULTIPC18

Бренд: Master Pumps Страницы: 32

Aeroflow Series

Бренд: Electrorad Страницы: 21

Бренд: EBARA Страницы: 172

WEATHERMAKER 50TFQ008

Бренд: Carrier Страницы: 28

SUBMERSIBLE DIRTY WATER PUMP 93819

Бренд: Pacific hydrostar Страницы: 14

Бренд: Protemp Страницы: 51

Бренд: Cadet Страницы: 2

Бренд: SHX Страницы: 27

Бренд: Flo Fab Страницы: 9

Бренд: Uberhaus Страницы: 14

PACIFIC HYDROSTAR 1/3 HP Submersible Sump Pump with Vertical Float...

Бренд: Pacific hydrostar Страницы: 9

SILICIUM 3 IN 1

Бренд: CLIMASTAR Страницы: 16

Бренд: Qlima Страницы: 164

Бренд: Pfeiffer Vacuum Страницы: 52

York YH9FYH12BAH-A-X

Бренд: Johnson Controls Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды