Daikin RXYQ5PY1 Скачать руководство пользователя страница 245 | Manualshive

Страница: 245 / 355

background image

SiEN34-705

Heat Pump / Cooling Only 50Hz (RX(Y)Q5~54P)

Installation Manual

239

1.7.1 Power circuit, safety device, and cable requirements

!

A power circuit (see the following table) must be provided for connection of the unit. This
circuit must be protected with the required safety devices, i.e. a main switch, a slow blow
fuse on each phase and an earth leakage circuit breaker.

!

When using residual current operated circuit breakers, be sure to use a high-speed type (1
second or less) 200mA rated residual operating current.

!

Use copper conductors only.

!

Use insulated wire for the power cord.

!

Select the power supply cable type and size in accordance with relevant local and national
regulations.

!

Specifications for local wiring are in compliance with IEC60245.

!

Use wire type H05VV when protected pipes are used.
Use wire type H07RN-F when protected pipes are not used.

Note:

The above table indicates power specifications for standard combinations (see 1-2
Introduction).
If using anything other than the above combinations in a multi system, calculate using the
following procedure.

Minimum circuit amp value: add the minimum circuit amp values for each independent unit
Recommended fuse capacity: select the fuse capacity with the next higher value of the
calculated minimum circuit amp. multiplied by 1.1.
Ex: Combining the RXYQ30PY1 using RXYQ8PY1, RXYQ10PY1, and RXYQ12PY1.
Minimum circuit amp. of the RXYQ8PY1 in table above = 18.5 A
Minimum circuit amp. of RXYQ10PY1 in table above = 21.6 A
Minimum circuit amp. of RXYQ12PY1 in table above = 22.7 A
Accordingly, the minimum circuit amp. of the RXYQ30PY1 = 18.5 + 21.6 + 22.7= 62.8 A
Multiplying the result above by 1.1 (62.8 × 1.1) = 69.1 A, so the recommended fuse capacity
would be 70 A.

Phase and

frequency

Voltage

Minimum circuit

amp.

Recommended

fuses

RX(Y)Q5PY1

φ

3, 50Hz

380-415V

11.9A

15A

RX(Y)Q8PY1

φ

3, 50Hz

380-415V

18.5A

25A

RX(Y)Q10PY1

φ

3, 50Hz

380-415V

21.6A

25A

RX(Y)Q12PY1

φ

3, 50Hz

380-415V

22.7A

25A

RX(Y)Q14PY1

φ

3, 50Hz

380-415V

31.5A

35A

RX(Y)Q16PY1

φ

3, 50Hz

380-415V

31.5A

35A

RX(Y)Q18PY1

φ

3, 50Hz

380-415V

32.5A

40A

RX(Y)Q20PY1

φ

3, 50Hz

380-415V

41.2A

50A

RX(Y)Q22PY1

φ

3, 50Hz

380-415V

44.3A

50A

RX(Y)Q24PY1

φ

3, 50Hz

380-415V

50.0A

60A

RX(Y)Q26PY1

φ

3, 50Hz

380-415V

51.0A

60A

RX(Y)Q28PY1

φ

3, 50Hz

380-415V

54.1A

60A

RX(Y)Q30PY1

φ

3, 50Hz

380-415V

55.2A

70A

RX(Y)Q32PY1

φ

3, 50Hz

380-415V

63.0A

70A

RX(Y)Q34PY1

φ

3, 50Hz

380-415V

64.0A

80A

RX(Y)Q36PY1

φ

3, 50Hz

380-415V

65.0A

80A

RX(Y)Q38PY1

φ

3, 50Hz

380-415V

73.7A

90A

RX(Y)Q40PY1

φ

3, 50Hz

380-415V

81.5A

90A

RX(Y)Q42PY1

φ

3, 50Hz

380-415V

82.5A

100A

RX(Y)Q44PY1

φ

3, 50Hz

380-415V

83.5A

100A

RX(Y)Q46PY1

φ

3, 50Hz

380-415V

86.6A

100A

RX(Y)Q48PY1

φ

3, 50Hz

380-415V

87.7A

100A

RX(Y)Q50PY1

φ

3, 50Hz

380-415V

96.5A

110A

RX(Y)Q52PY1

φ

3, 50Hz

380-415V

96.5A

110A

RX(Y)Q54PY1

φ

3, 50Hz

380-415V

97.5A

110A

«
...
243
244
245
246
247
...
»

Содержание RXYQ5PY1




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RXYQ5PY1

Бренд: Maag Страницы: 16

Evosta2 11/139 SAN V

Бренд: DAB Страницы: 31

Бренд: DAB Страницы: 19

Бренд: Haverland Страницы: 64

Vectissimo CO180

Бренд: Rowenta Страницы: 10

Бренд: Dupla MARIN Страницы: 28

ARO PP10A Series

Бренд: Ingersoll-Rand Страницы: 12

ULTRASlimline 10222

Бренд: Seville Classics Страницы: 6

Бренд: vacuubrand Страницы: 70

Бренд: L.B. White Страницы: 24

Бренд: Bryant Страницы: 54

Бренд: Omega Altise Страницы: 8

XCT 7 40VC009-048F-7G-QEE

Бренд: Carrier Страницы: 28

Бренд: Simfer Страницы: 15

Бренд: iGenix Страницы: 5

Бренд: Grundfos Страницы: 8

Бренд: Dimplex Страницы: 52

Бренд: Armstrong Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды