manualshive.com logo in svg

Daikin RXYQ5PY1, Руководство по обслуживанию

На нашем сайте вы можете скачать бесплатно сервисный мануал для Daikin RXYQ5PY1. Этот руководство поможет вам правильно обслуживать и настраивать ваш кондиционер. Скачайте его сейчас с manualshive.com и получите подробные инструкции по эксплуатации вашего устройства.

Поделиться
Скачать
background image

SiEN34-705

Heat Pump 60Hz (RXYQ5~54P)

Installation Manual

305

2.12 Onsite Settings

Note:

In the case of a multi system, all onsite settings should be made on the master unit. Settings 
made on sub units are invalid.
The outdoor unit to which the indoor unit transmission wire are connected is the master unit, 
and all other units are sub units.

2.12.1 Onsite Settings with the Power Off

If the COOL/HEAT selector was connected to the outdoor unit in  “2-7. Field Wiring”, set the dip 
switch (DS1) on the outdoor unit PC-board (A1P) to “ON” (it is set to “OFF” when shipped from 
the factory).

For the position of the dip switch (DS1), see the “Service Precautions” label (see at right) which 
is attached to the EL. COMPO. BOX lid.

Warning

 Electric Shock Warning:

Never perform with the power on.
There is a serious risk of electric shock if any live part is touched.

2.12.2 Onsite Settings with the Power On

Use the push button switches (BS1 through BS5) on the outdoor unit PC-board (A1P) to make 
the necessary onsite settings.
See the “Service Precautions” label on the EL. CONPO. BOX lid for details on the positions and 
operating method of the push button switches and on the onsite setting.
Make sure to record the setting on the accessory “REQUEST FOR THE INDICATION” label.

Warning

 Electric Shock Warning:

Use an insulated rod to operate the push buttons via the inspection door of EL. COMPO. BOX 
lid.
There is a risk of electric shock if you touch any live parts, since this operation must be 
performed with the power on.

Inspection 
door

[Service Precautions] 
label

EL.COMPO. 
BOX lid

Содержание RXYQ5PY1




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RXYQ5PY1

Balboa GS100 Operation Manual preview
GS100
Бренд: Balboa Страницы: 2
Fedders C12 Specification Sheet preview
C12
Бренд: Fedders Страницы: 4
Danfoss DHP-A Installation Manual preview
DHP-A
Бренд: Danfoss Страницы: 64
Danfoss DHP-A Service Instructions Manual preview
DHP-A
Бренд: Danfoss Страницы: 86
Danfoss DHP-A User Manual preview
DHP-A
Бренд: Danfoss Страницы: 28
Vornado GLIDE HEAT Owner'S Manual preview
GLIDE HEAT
Бренд: Vornado Страницы: 15
Jaga MINF Mounting Instructions preview
MINF
Бренд: Jaga Страницы: 6
Becker BASIC VASF 2.120/1-0.AC115 Operating Instructions Manual preview
BASIC VASF 2.120/1-0.AC115
Бренд: Becker Страницы: 6
Hetr H1017 Operating Instructions And Manual preview
H1017
Бренд: Hetr Страницы: 4
Aquael AQUAJET PFN 10000 PLUS Operating Manual preview
AQUAJET PFN 10000 PLUS
Бренд: Aquael Страницы: 54
Easy@Home PTC-156 User Manual preview
PTC-156
Бренд: Easy@Home Страницы: 38
DAYLIFF DDW 400S Installation & Operating Manual preview
DDW 400S
Бренд: DAYLIFF Страницы: 12
AMICOCIRC AMICO 20-4-130 Handbook preview
AMICO 20-4-130
Бренд: AMICOCIRC Страницы: 13
Gardena IP 300 7944 Operating Instructions Manual preview
IP 300 7944
Бренд: Gardena Страницы: 17
Jaga Heatwave large Mounting Instructions preview
Heatwave large
Бренд: Jaga Страницы: 11
Eaton 70122 Manual preview
70122
Бренд: Eaton Страницы: 21
Dimplex BWP 301 L Installation And Operating Instructions Manual preview
BWP 301 L
Бренд: Dimplex Страницы: 44
Liebert TCDV165 Product Information Manual preview
TCDV165
Бренд: Liebert Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды