Daikin RXYQ5PY1 Скачать руководство пользователя страница 108

Страница: 108 / 355

Test Operation

SiEN34-705

102

General Information

For setting items of (*1), refer to detailed information provided on page 112 onward.

Setting by dip switches

Using dip switches on the PC board enables field setting shown below. However, make no
changes of factory settings except for DS1-1.

Setting item

Content and objective of setting

Overview of setting procedure

Service setting

Indoor unit fan

forced H operation

Used to operate the indoor unit in the

stopped state in forced H operation mode.

Set No. 5 of "Setting mode 2" to indoor unit

forced fan H.

Indoor unit forced

operation

Used to operate the indoor unit in forced

operation mode.

Set No. 6 of "Setting mode 2" to indoor unit

forced operation mode.

Change of targeted

evaporating

temperature

(in cooling)

In cooling operation, used to change the

targeted evaporating temperature for

compressor capacity control.

Select high side or low side with No. 8 of

"Setting mode 2".

Change of targeted

condensing

temperature

(in heating)

In heating operation, used to change the

targeted condensing temperature for

compressor capacity control.

Select high side or low side with No. 9 of

"Setting mode 2".

Setting of defrost

selection

*Heat Pump model

only

Used to change a temperature at which the

defrost operation is initiated, thus making

the initiation easy or hard.

Select fast side or slow side with No. 10 of

"Setting mode 2".

Setting of

sequential startup

Used to start units not in sequence but

simultaneously.

Set No. 11 of "Setting mode 2" to NONE.

Emergency

operation

If the compressor has a failure, used to

prohibit the operation of compressor(s)

concerned or outdoor unit(s) concerned

and to conduct emergency operation of the

system only with operable compressor(s)

or outdoor unit(s).

Make this setting while in "Setting mode 2".

For system with a single outdoor unit: Set

with No. 19 or 42.

For system with multiple outdoor units: Set

with No. 38, 39, or 40.

Additional

refrigerant

charging (*1)

If a necessary amount of refrigerant cannot

be charged due to the stop of outdoor unit,

operate the outdoor unit and then refill

refrigerant.

Set No. 20 of "Setting mode 2" to ON and

then charge refrigerant.

Refrigerant

recovery mode (*1)

Used to recover refrigerant on site.

With operations of indoor and outdoor units

prohibited, fully open the expansion valve

of the indoor and outdoor units.

Set No. 21 of "Setting mode 2" to ON.

Vacuuming mode

(*1)

Used to conduct vacuuming on site.

Fully open the expansion valves of the

indoor and outdoor units, and energize part

of solenoid valves. Use a vacuum pump to

conduct vacuuming.

Set No. 21 of "Setting mode 2" to ON.

ENECUT test

operation

Used to forcedly turn ON the ENECUT.

(Be noted this mode is not functional with

the indoor unit remote control turned ON.)

Set No. 24 of "Setting mode 2" to ON.

Power transistor

check mode

Used for the troubleshooting of DC

compressors.

Inverter waveform output makes it possible

to judge whether a malfunction results from

the compressor or the PC board.

Set No. 28 of "Setting mode 2" to ON.

Setting of model

with spare PC

board

In order to replace the PC board by a spare

one, be sure to make model setting.

For this setting, set the DS2-2, -3, and-4

switches on the PC board to the model

concerned.

Dipswitch

Setting item

Description

No.

Setting

DS1-1

Cool / Heat select

Used to set cool / heat select by Cool/Heat selector

equipped with outdoor unit.

• Heat Pump model only

OFF (Factory set)

DS1-2

~DS1-4

Not used

Do not change the factory settings.

OFF (Factory set)

DS2-1

Not used

Do not change the factory settings.

OFF (Factory set)

Содержание RXYQ5PY1




































































































































































































































































































































































Результаты поиска

Содержание RXYQ5PY1

Отзывы:

Похожие инструкции для RXYQ5PY1

Бренды по названию

Популярные бренды

Daikin RXYQ5PY1, Руководство по обслуживанию

Результаты поиска

Содержание RXYQ5PY1

Отзывы:

Похожие инструкции для RXYQ5PY1

Бренды по названию

Популярные бренды