Daikin RXYQ5PY1 Скачать руководство пользователя страница 348

Страница: 348 / 355

SiEN34-705

Precautions for New Refrigerant (R-410A)

Precautions for New Refrigerant (R-410A)

341

Temperature scale indicates the relationship between pressure and temperature in gas
saturated state.

Differences

Change in pressure

Change in service port diameter

7. Charge hose for R-410A

Specifications

Working pressure 5.08 MPa (51.8 kg/cm

)

Rupture pressure 25.4 MPa (259 kg/cm

)

Available with and without hand-operate valve that prevents refrigerant from outflow.

Differences

Pressure proof hose

Change in service port diameter

Use of nylon coated material for HFC resistance

8. Charging cylinder

Specifications

Use weigher for refrigerant charge listed below to charge directly from refrigerant cylinder.

Differences

The cylinder can not be used for mixed refrigerant since mixing ratio is changed during
charging.

When R-410A is charged in liquid state using charging cylinder, foaming phenomenon is
generated inside charging cylinder.

(Ho

e with

ll v

lve)

Can not be used

Содержание RXYQ5PY1




































































































































































































































































































































































Результаты поиска

Содержание RXYQ5PY1

Отзывы:

Похожие инструкции для RXYQ5PY1

Бренды по названию

Популярные бренды

Daikin RXYQ5PY1, Руководство по обслуживанию

Результаты поиска

Содержание RXYQ5PY1

Отзывы:

Похожие инструкции для RXYQ5PY1

Бренды по названию

Популярные бренды