Daikin RXYQ5PY1 Скачать руководство пользователя страница 334 | Manualshive

Страница: 334 / 355

background image

SiEN34-705

Operation Manual

Operation Manual

327

MOVEMENT OF THE AIR FLOW FLAP

For the following conditions, a micro computer controls the air flow
direction which may be different from the display.

The air flow direction can be adjusted in one of the following ways.

• The air flow flap itself adjusts its position.
• The air flow direction can be fixed by the user.

Automatic “

” or desired position “

”.

(Refer to figure 13)

Note

•

The movable limit of the flap is changeable. Contact your
Daikin dealer for details. (Only for FXC, FXF, FXH, FXK,
FXA)

• Avoid operating in the horizontal direction “

”. It may

cause dew or dust to settle on the ceiling.

2-6-4 Programming Start and Stop of the System with

Timer
(Refer to figure 9)

• The timer is operated in the following two ways.

Programming the stop time “

”. The system stops

operating after the set time has elapsed.
Programming the start time “

”. The system starts

operating after the set time has elapsed.

• The timer can be programmed for a maximum of 72 hours.
• The start and the stop time can be simultaneously pro-

grammed.

Press the timer mode start/stop button several times and
select the mode on the display.
The display flashes.

•

For setting the timer stop “

”

•

For setting the timer start “

”

Press the programming time button and set the time for stop-
ping or starting the system.

Each time this button is pressed, the time advances
or goes backward by 1 hour.

Press the timer on/off button.
The timer setting procedure ends. The display “

” or

“

” changes from flashing light to constant light.

Note

•

When setting the timer off and on at the same time, repeat
the above procedure (from “

” to “

”) once again.

• After the timer is programmed, the display shows the

remaining time.

• Press the timer on/off button once again to cancel program-

ming. The display vanishes.

For example: (Refer to figure 11)

When the timer is programmed to stop the system after 3
hours and start the system after 4 hours, the system will stop
after 3 hours and start 1 hour later.

2-6-5 Setting the Master Remote Control

(Refer to figure 10)

COOLING

HEATING

• When starting operation.
• When the room temperature is

higher than the set temperature.

• At defrost operation.

• When operating continuously at horizontal air flow direction.
• When continuous operation with downward air flow is performed at

the time of cooling with a ceiling-suspended or a wall-mounted
unit, the microcomputer may control the flow direction, and then
the remote control indication also will change.

Double-flow (FXC)

Ceiling Suspended (FXH)

Wall Mounted (FXA)

Multi-flow (FXF)

Corner (FXK)

figure 13

figure 9

1

2

3

1

3

figure 11

figure 10

«
...
332
333
334
335
336
...
»

Содержание RXYQ5PY1




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RXYQ5PY1

Бренд: Sanden Страницы: 26

Бренд: Nectre Fireplaces Страницы: 17

Бренд: Gardena Страницы: 17

Бренд: Saci Страницы: 24

Бренд: Calpeda Страницы: 4

Бренд: Q-Pumps Страницы: 44

Бренд: Wayne Страницы: 8

Бренд: DAB Страницы: 12

Бренд: Calpeda Страницы: 27

WILDEN P100 Advanced Plastic

Бренд: PSG Dover Страницы: 28

Бренд: Haverland Страницы: 64

Vectissimo CO180

Бренд: Rowenta Страницы: 10

Бренд: PAPILLON Страницы: 16

HOT Splash HS40

Бренд: Duratech Страницы: 36

Comfort SC-FH53015

Бренд: Scarlett Страницы: 8

Бренд: Nakayama Страницы: 29

REMINGTON REM-16-TTC-O

Бренд: Pinnacle Climate Technologies Страницы: 32

Бренд: True North Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды