Daikin RXYQ5PY1 Скачать руководство пользователя страница 332 | Manualshive

Страница: 332 / 355

background image

SiEN34-705

Operation Manual

Operation Manual

325

FOR SYSTEMS WITHOUT COOL/HEAT SELECTOR (Refer to
figure 4)

Press the operation mode selector button several times and
select the operation mode of your choice;
“

” Cooling operation

“

” Heating operation

“

” Fan only operation

Press the on/off button.
The operation lamp lights up and the system starts operation.

FOR SYSTEMS WITH COOL/HEAT SELECTOR
(Refer to figures 4 and 7)

Select operation mode with the Cool/Heat selector as follows:
“

” “

” Cooling operation

(Refer to figure 7.1)

“

” “

” Heating operation

(Refer to figure 7.2)

“

”

“

”

Fan only operation

(Refer to figure 7.3)

Press the on/off button.

(Refer to figure 4)

The operation lamp lights up and the system starts operation.

ADJUSTMENT (Refer to figure 4)

For adjusting the desired temperature, fan speed and air flow
direction (only for FXC, FXF, FXH, FXK, FXA), follow the pro-
cedure shown below.

Press the temperature setting button and set the desired tem-
perature.

Each time this button is pressed, the temperature
setting rises or lowers 1°C.

Note

•

Set the temperature within the operation range.

•

The temperature setting is impossible for fan only opera-
tion.

Press the fan speed control button and select the fan speed of
your preference.
Press air flow direction adjust button.
Refer to the chapter “Adjusting the Air Flow Direction” for
details.

STOPPING THE SYSTEM (Refer to figure 4)

Press the on/off button once again.
The operation lamp goes off and the system stops operation.

Note

•

Do not turn off the power immediately after the unit stops.

•

The system need at least 5 minutes for residual operation
of drain pump device.
Turning off the power immediately will cause water leak or
trouble.

EXPLANATION OF HEATING OPERATION

• For general heating operation, it may take longer to reach the set

temperature than in cooling operation.
We recommend starting the operation which was used before
using timer operation.

• The following operation is performed in order to prevent the heat-

ing capacity from dropping or cold air from blowing.

Defrost operation

•

In heating operation, freezing of the outdoor unit heat
exchanger increases. Heating capability decreases and the
system goes into defrost operation.

•

The indoor unit fan stops and the remote control displays

“

”.

•

After maximum 10 minutes of defrost operation, the system
returns to heating operation again.

Hot start

•

In order to prevent cold air from blowing out of an indoor
unit at the start of heating operation, the indoor fan is auto-
matically stopped. The display of the remote control shows
“

”.

figure 4

1

2

figure 7.1

figure 7.2

figure 7.3

1

2

3

4

5

6

«
...
330
331
332
333
334
...
»

Содержание RXYQ5PY1




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RXYQ5PY1

Бренд: Davey Страницы: 12

Бренд: Barmesa Pumps Страницы: 42

Бренд: laguna Страницы: 24

Бренд: Nachfolger Страницы: 2

Бренд: T.I.P. Страницы: 24

Бренд: Taco Страницы: 12

ACQUITY UPLC I-Class IVD

Бренд: Waters Страницы: 98

MULTIMAXX HG 24

Бренд: FläktGroup Страницы: 63

Бренд: ProMinent Страницы: 77

KLIMATRONIC HEAT SUPREME

Бренд: Suntec Wellness Страницы: 124

Бренд: Nakayama Страницы: 29

SINGLE PACKAGE DUAL FUEL HEAT PUMP

Бренд: York Страницы: 8

Бренд: Rotex Страницы: 80

FLOJET G55 Series

Бренд: Xylem Страницы: 2

Бренд: Rinnai Страницы: 34

Бренд: Sentiotec Страницы: 28

Бренд: Xylem Страницы: 20

Бренд: Qlima Страницы: 176

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды