Renesas SH7041 Series Hardware Manual Download Page 12

Page: 12 / 923

Section

Page

Description

22.7.2 Program-
Verify Mode

Figure 22.13
Program/Program
Verify Flow

706

Figure amended

Set SWE bit in FLMCR1

m = 0

Write 32-byte data in reprogram data area

in RAM to flash memory consecutively

Start of programming

Store 32-byte program data in

reprogram data area

Read verify data

Clear SWE bit in FLMCR1

m = 1

End of programming

Program data = verify data?

End of 32-byte

data verification?

flag = 0?

Verify

Increment address

Programming failure

Clear SWE bit in FLMCR1

≥

1000

←

n + 1

Start

End of programming

Enable WDT

Disable WDT

Reprogram data computation

Transfer reprogram data to reprogram

data area

Wait 10

Clear PV1(2) bit in FLMCR1(2)

Wait 4

Dummy write of H'FF to verify address

Wait 2

Set PV1(2) bit in FLMCR1(2)

Wait 4

Clear PSU1(2) bit in FLMCR1(2)

Wait 10

Clear P1(2) bit in FLMCR1(2)

Wait 10

Set P1(2) bit in FLMCR1(2)

Wait 200

Set PSU1(2) bit in FLMCR1(2)

Wait 50

Note

5 added.

5 Make sure to set the wait times and repetitions as specified.

Programming may not complete correctly if values other than
the specified ones are used.

Summary of Contents for SH7041 Series




























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SH7041 Series

Reviews:

Renesas SH7041 Series, Hardware Manual, Page: 12 / 923

Search results

Summary of Contents for SH7041 Series

Reviews: