manualshive.com logo in svg

IBM System x3650 M5, Installation And Service Manual, Page: 982 / 1010

Share
Download
IBM System x3650 M5 Installation And Service Manual Download Page 982

166-904-001

IMM I2C Test Failed

Explanation:

IMM Indicates failure in PCA9557--I2C I/O Expander bus (BUS 3).

Severity:

Error

Serviceable:

Yes

Recoverable:

No

Automatically notify Support:

No

User response:

Perform the actions mentioned one at a time and try the test after each action:

1.

Turn off the system and disconnect it from power. Wait for 45 seconds. Reconnect it to power.

2.

Make sure that DSA and BMC/IMM are at the latest level.

3.

Run the test again.

4.

If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service Guide" for the
next corrective action.

Related Links:

v

IBM Support Website

v

Latest level of DSA

v

Latest level of BMC/IMM

166-907-001

IMM I2C Test Failed

Explanation:

IMM Indicates failure in PCA9545--4-Channel I2C Switch bus (BUS 6).

Severity:

Error

Serviceable:

Yes

Recoverable:

No

Automatically notify Support:

No

User response:

Perform the actions mentioned one at a time and try the test after each action:

1.

Turn off the system and disconnect it from power. Wait for 45 seconds. Reconnect it to power.

2.

Make sure that DSA and BMC/IMM are at the latest level.

3.

Run the test again.

4.

If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service Guide" for the
next corrective action.

Related Links:

v

IBM Support Website

v

Latest level of DSA

v

Latest level of BMC/IMM

166-904-001 • 166-907-001

966

System x3650 M5 Type 5462: Installation and Service Guide

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments