IBM System x3650 M5 Installation And Service Manual Download Page 237

Page: 237 / 1010

Connect the front video cable to the system board.

10.

Replace the fan cage assembly (see “Replacing the fan cage assembly” on page
173).

11.

Replace the top cover (see “Replacing the top cover” on page 147).

12.

Slide the server into the rack.

13.

Reconnect the power cords and any cables that you removed.

14.

Turn on the peripheral devices and the server.

Screws

Figure 165. Screw installation

Front video cable

Figure 166. Cable connection

Chapter 5. Removing and replacing components

221

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M5

Reviews:

IBM System x3650 M5, Installation And Service Manual, Page: 237 / 1010

Search results

Summary of Contents for System x3650 M5

Reviews: