IBM System x3650 M5 Installation And Service Manual Download Page 268

Page: 268 / 1010

Carefully insert the LCD system information display panel into place.

Insert the retention bracket into the slot on the media cage and push it until it
clicks into place.

Media cage

Retention bracket

Figure 205. Retention bracket removal

Media cage

LCD system information
display panel

Alignment pins

Figure 206. LCD system information display panel installation

252

System x3650 M5 Type 5462: Installation and Service Guide

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M5

Reviews:

IBM System x3650 M5, Installation And Service Manual, Page: 268 / 1010

Search results

Summary of Contents for System x3650 M5

Reviews: