manualshive.com logo in svg

IBM System x3650 M5, Installation And Service Manual, Page: 408 / 1010

Share
Download
IBM System x3650 M5 Installation And Service Manual Download Page 408

80010b01-1404ffff

Numeric sensor [NumericSensorElementName] going high (upper non-recoverable) has

asserted. (DIMM CD VR Temp)

Explanation:

This message is for the use case when an implementation has detected an Upper Non-recoverable

sensor going high has asserted.

May also be shown as 80010b011404ffff or 0x80010b011404ffff

Severity:

Error

Alert Category:

Critical - Temperature

Serviceable:

Yes

CIM Information: Prefix:

PLAT and

ID:

0498

SNMP Trap ID:

0

Automatically notify Support:

No

User response:

1.

Make sure that the fans are operating, that there are no obstructions to the airflow (front and rear of the server),

that the air baffle is in place and correctly installed, and that the server cover is installed and completely closed.

2.

Check the ambient temperature. You must be operating within the specifications (see Server Features and

specifications for more information).

3.

(Trained technician only) Replace system board.

80010b01-1405ffff

Numeric sensor [NumericSensorElementName] going high (upper non-recoverable) has

asserted. (DIMM EF VR Temp)

Explanation:

This message is for the use case when an implementation has detected an Upper Non-recoverable

sensor going high has asserted.

May also be shown as 80010b011405ffff or 0x80010b011405ffff

Severity:

Error

Alert Category:

Critical - Temperature

Serviceable:

Yes

CIM Information: Prefix:

PLAT and

ID:

0498

SNMP Trap ID:

0

Automatically notify Support:

No

User response:

1.

Make sure that the fans are operating, that there are no obstructions to the airflow (front and rear of the server),

that the air baffle is in place and correctly installed, and that the server cover is installed and completely closed.

2.

Check the ambient temperature. You must be operating within the specifications (see Server Features and

specifications for more information).

3.

(Trained technician only) Replace system board.

80010b01-1404ffff • 80010b01-1405ffff

392

System x3650 M5 Type 5462: Installation and Service Guide

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments