IBM System x3650 M5 Installation And Service Manual Download Page 350

Page: 350 / 1010

40000030-00000000

IPv6 disabled by user [arg1] .

Explanation:

IPv6 protocol is disabled by user

May also be shown as 4000003000000000 or 0x4000003000000000

Severity:

Info

Alert Category:

none

Serviceable:

CIM Information: Prefix:

IMM and

ID:

0048

SNMP Trap ID:

Automatically notify Support:

User response:

Information only; no action is required.

40000031-00000000

IPv6 static IP configuration enabled by user [arg1].

Explanation:

IPv6 static address assignment method is enabled by user

May also be shown as 4000003100000000 or 0x4000003100000000

Severity:

Info

Alert Category:

none

Serviceable:

CIM Information: Prefix:

IMM and

ID:

0049

SNMP Trap ID:

Automatically notify Support:

User response:

Information only; no action is required.

40000032-00000000

IPv6 DHCP enabled by user [arg1].

Explanation:

IPv6 DHCP assignment method is enabled by user

May also be shown as 4000003200000000 or 0x4000003200000000

Severity:

Info

Alert Category:

none

Serviceable:

CIM Information: Prefix:

IMM and

ID:

0050

SNMP Trap ID:

Automatically notify Support:

User response:

Information only; no action is required.

40000030-00000000 • 40000032-00000000

334

System x3650 M5 Type 5462: Installation and Service Guide

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M5

Reviews:

IBM System x3650 M5, Installation And Service Manual, Page: 350 / 1010

Search results

Summary of Contents for System x3650 M5

Reviews: