IBM System x3650 M5 Installation And Service Manual Download Page 333

Page: 333 / 1010

Table 16. Events that automatically notify Support (continued)

Event ID

Message String

Automatically
Notify
Support

806f060d-0413ffff

Array [ComputerSystemElementName] has
failed. (Drive 19)

Yes

806f060d-0414ffff

Array [ComputerSystemElementName] has
failed. (Drive 20)

Yes

806f060d-0415ffff

Array [ComputerSystemElementName] has
failed. (Drive 21)

Yes

806f060d-0416ffff

Array [ComputerSystemElementName] has
failed. (Drive 22)

Yes

806f060d-0417ffff

Array [ComputerSystemElementName] has
failed. (Drive 23)

Yes

806f060d-0418ffff

Array [ComputerSystemElementName] has
failed. (Drive 24)

Yes

806f060d-0419ffff

Array [ComputerSystemElementName] has
failed. (Drive 25)

Yes

806f060d-041affff

Array [ComputerSystemElementName] has
failed. (Drive 26)

Yes

806f060d-041bffff

Array [ComputerSystemElementName] has
failed. (Drive 27)

Yes

806f060d-041cffff

Array [ComputerSystemElementName] has
failed. (Drive 28)

Yes

806f060d-041dffff

Array [ComputerSystemElementName] has
failed. (Drive 29)

Yes

806f060d-041effff

Array [ComputerSystemElementName] has
failed. (Drive 30)

Yes

806f060d-041fffff

Array [ComputerSystemElementName] has
failed. (Drive 31)

Yes

806f0813-2581ffff

A Uncorrectable Bus Error has occurred on
system [ComputerSystemElementName].
(DIMMs)

Yes

806f0813-2582ffff

A Uncorrectable Bus Error has occurred on
system [ComputerSystemElementName].
(PCIs)

Yes

806f0813-2584ffff

A Uncorrectable Bus Error has occurred on
system [ComputerSystemElementName].
(CPUs)

Yes

Appendix A. Integrated management module II (IMM2) error messages

317

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M5

Reviews:

IBM System x3650 M5, Installation And Service Manual, Page: 333 / 1010

Search results

Summary of Contents for System x3650 M5

Reviews: