IBM System x3650 M5 Installation And Service Manual Download Page 160

Page: 160 / 1010

12x3.5-inch drive model

The internal routing for the 12x3.5-inch drive model cables.

The following illustration shows the internal routing for the 12x3.5-inch drive
model cables.

12x3.5-inch hot-swap hard disk drive model

12x3.5-inch hot-swap hard disk drive

SAS signal cable

Power / configuration
cable

SAS 0

SAS 1

Figure 66. 8x3.5-inch hot-swap hard disk drives cabling

144

System x3650 M5 Type 5462: Installation and Service Guide

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M5

Reviews:

IBM System x3650 M5, Installation And Service Manual, Page: 160 / 1010

Search results

Summary of Contents for System x3650 M5

Reviews: