manualshive.com logo in svg

IBM System x3650 M5, Installation And Service Manual, Page: 158 / 1010

Share
Download
IBM System x3650 M5 Installation And Service Manual Download Page 158

3.5-inch hard disk drive cable connection

The following illustrations show the cabling information for the 3.5-inch drive
models.

Important:

Make sure all SAS cables are routed lower than the DIMM latches.

8x3.5-inch drive model

The internal routing for the 8x3.5-inch drive model cables.

The following illustration shows the internal routing for the 8x3.5-inch drive model
cables.

8x3.5-inch simple-swap hard disk drive model

v

8x3.5-inch simple-swap hard disk drive with hardware RAID

v

8x3.5-inch simple-swap hard disk drive with software RAID

SAS signal cable

Power / configuration
cable

Figure 64. 8x3.5-inch simple-swap hard disk drives with hardware RAID cabling

142

System x3650 M5 Type 5462: Installation and Service Guide

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments