manualshive.com logo in svg

IBM System x3650 M5, Installation And Service Manual, Page: 878 / 1010

Share
Download
IBM System x3650 M5 Installation And Service Manual Download Page 878

401-801-000

EXA Port Ping Test Aborted

Explanation:

EXA Port Ping Test Aborted. Unable to get device base address.

Severity:

Warning

Serviceable:

Yes

Recoverable:

No

Automatically notify Support:

No

User response:

Complete the following steps:

1.

Remove power cables, wait for 45 seconds, reconnect and rerun the test.

2.

Make sure that the scalability cable connections are as per specification.

3.

Make sure that DSA and BIOS/uEFI are at the latest level.

4.

If the problem remains, contact your technical-service representative.

Related Links:

v

IBM Support Website

v

Latest level of DSA

v

Latest level of BMC/IMM

401-802-000

EXA Port Ping Test Aborted

Explanation:

EXA Port Ping Test Aborted. Port connections may not be correct.

Severity:

Warning

Serviceable:

Yes

Recoverable:

No

Automatically notify Support:

No

User response:

Complete the following steps:

1.

Remove power cables, wait for 45 seconds, reconnect and rerun the test.

2.

Make sure that the scalability cable connections are as per specification.

3.

Make sure that DSA and BIOS/uEFI are at the latest level.

4.

If the problem remains, contact your technical-service representative.

Related Links:

v

IBM Support Website

v

Latest level of DSA

v

Latest level of BMC/IMM

401-801-000 • 401-802-000

862

System x3650 M5 Type 5462: Installation and Service Guide

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments