IBM System x3650 M5 Installation And Service Manual Download Page 149

Page: 149 / 1010

2.5-inch hard disk drive cable connection

The following illustrations show the cabling information for the 2.5-inch drive
models.

Important:

Make sure all SAS cables are routed lower than the DIMM latches.

8x2.5-inch drive model

The internal routing for the 8x2.5-inch drive model cables.

The following illustration shows the internal routing for the 8x2.5-inch drive model
cables.

8x2.5-inch simple-swap hard disk drive model

8x2.5-inch simple-swap hard disk drive with hardware RAID

8x2.5-inch simple-swap hard disk drive with software RAID

SAS signal cable

Power / configuration
cable

Figure 49. 8x2.5-inch simple-swap hard disk drive with hardware RAID cabling

Chapter 5. Removing and replacing components

133

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M5

Reviews:

IBM System x3650 M5, Installation And Service Manual, Page: 149 / 1010

Search results

Summary of Contents for System x3650 M5

Reviews: