manualshive.com logo in svg

IBM System x3650 M5, Installation And Service Manual, Page: 35 / 1010

Share
Download
IBM System x3650 M5 Installation And Service Manual Download Page 35

Front view

The following illustrations show the controls, LEDs, and connectors on the front of
your server model.

2.5-inch hard disk drive server model.

v

8 hard-disk drive configuration / 16 hard-disk drive configuration front view

v

24 hard-disk drive configuration front view

3.5-inch hard disk drive server model.

v

8 hard-disk drive configuration front view

Hard disk drive
activity LED (green)

Hard disk drive
status LED (yellow)

Hard disk
drive bays

Rack
release
latch

LCD system
information
display panel

Operator
information panel

CD/DVD
eject button

CD/DVD drive
activity LED

Rack
release
latch

CD/DVD drive
(optical drive)

Bay 7

Bay 0

Video
connector

USB connectors

User information tag

Figure 10. 8 hard-disk drive configuration / 16 hard-disk drive configuration front view

Hard disk drive
activity LED (green)

Hard disk drive
status LED (yellow)

Rack
release
latch

USB connectors

Operator
information panel

Rack
release
latch

Video
connector

User information tag

Figure 11. 24 hard-disk drive configuration front view

Rack
release
latch

Operator
information panel

Rack
release
latch

Video
connector

LCD system
information
display panel

USB connectors

CD/DVD
eject button

CD/DVD drive
activity LED

Hard disk drive
activity LED (green)

Hard disk drive
status LED (yellow)

User information tag

Figure 12. 8 hard-disk drive configuration front view

Chapter 1. The System x3650 M5 server

19

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments