IBM System x3650 M5 Installation And Service Manual Download Page 38 | Manualshive

Page: 38 / 1010

IBM System x3650 M5 Installation And Service Manual Download Page 38

the LCD system information display panel, the operator information panel or on
the system board is also lit to help isolate the error. This LED is controlled by
the IMM.

LCD system information display panel

Use this information for an overview of the LCD system information display panel,
which displays various types of information about the server.

The LCD system information display panel is on the front of the server. The LCD
system information display panel enables you to have quick access to system
status, firmware, network, and health information. The following illustration shows
the controls on the LCD system information display panel.

v

Scroll up button:

Press this button to scroll up or scroll to the left in the main

menu to locate and select the system information that you want displayed.

v

Select button:

Press this button to make your selection from the menu options.

v

Scroll down button:

Press this button to scroll down or scroll to the right in the

main menu to location and select the system information that you want
displayed.

The following is an illustration of the LCD system information display panel menu
options flow.

LCD system information display panel

Scroll down button

Scroll up button

Select button

Figure 16. LCD system information display panel

22

System x3650 M5 Type 5462: Installation and Service Guide

«
...
36
37
38
39
40
...
»

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments