manualshive.com logo in svg

IBM System x3650 M5, Installation And Service Manual, Page: 848 / 1010

Share
Download
IBM System x3650 M5 Installation And Service Manual Download Page 848

W.305800B

[W.305800B]

Explanation:

DRIVER HEALTH PROTOCOL: Reports 'Reboot' Required Controller. DRIVER HEALTH PROTOCOL:

Reports 'Reboot' Required Controller

Severity:

Warning

User response:

Complete the following steps:

1.

No action required. The system will reboot at the end of POST.

2.

If the problem persists, switch to the backup UEFI image or update the current UEFI image.

3.

Replace the system board.

W.305800C

[W.305800C]

Explanation:

DRIVER HEALTH PROTOCOL: Reports 'System Shutdown' Required Controller. DRIVER HEALTH

PROTOCOL: Reports 'System Shutdown' Required Controller

Severity:

Warning

User response:

Complete the following steps:

1.

No action required. The system will reboot at the end of POST.

2.

If the problem persists, switch to the backup UEFI image or update the current UEFI image.

3.

Replace the system board.

W.305800D

[W.305800D]

Explanation:

DRIVER HEALTH PROTOCOL: Disconnect Controller Failed. Requires 'Reboot'. DRIVER HEALTH

PROTOCOL: Disconnect Controller Failed. Requires 'Reboot'

Severity:

Warning

User response:

Complete the following steps:

1.

No action required. The system will reboot at the end of POST.

2.

If the problem persists, switch to the backup UEFI image or update the current UEFI image.

3.

Replace the system board.

W.305800E

[W.305800E]

Explanation:

DRIVER HEALTH PROTOCOL: Reports Invalid Health Status Driver. DRIVER HEALTH PROTOCOL:

Reports Invalid Health Status Driver

Severity:

Warning

User response:

Complete the following steps:

1.

No action required. The system will reboot at the end of POST.

2.

If the problem persists, switch to the backup UEFI image or update the current UEFI image.

3.

Replace the system board.

W.305800B • W.305800E

832

System x3650 M5 Type 5462: Installation and Service Guide

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments