IBM System x3650 M5 Installation And Service Manual Download Page 317

Page: 317 / 1010

If the expander is installed in slot 2, connect and route cables as the
following illustrations.

SAS signal cables

Power / configuration
cables

SAS 0 SAS 1

SAS 1 SAS 0

Figure 262. Cable routing

2.5-inch HDD hot-swap backplane

Power / configuration cable

SAS signal cable

Power / configuration cable

2.5-inch HDD hot-swap
backplane (expander)

Power / configuration cable

2.5-inch HDD hot-swap
backplane (expander)

SAS signal cable

Figure 263. Cable connections

Chapter 5. Removing and replacing components

301

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M5

Reviews:

IBM System x3650 M5, Installation And Service Manual, Page: 317 / 1010

Search results

Summary of Contents for System x3650 M5

Reviews: