manualshive.com logo in svg

IBM System x3650 M5, Installation And Service Manual, Page: 488 / 1010

Share
Download
IBM System x3650 M5 Installation And Service Manual Download Page 488

806f011b-0701ffff

The connector [PhysicalConnectorElementName] has encountered a configuration error. (Front

USB)

Explanation:

This message is for the use case when an implementation has detected an Interconnect Configuration

Error.

May also be shown as 806f011b0701ffff or 0x806f011b0701ffff

Severity:

Error

Alert Category:

Critical - Other

Serviceable:

Yes

CIM Information: Prefix:

PLAT and

ID:

0266

SNMP Trap ID:

50

Automatically notify Support:

Yes

User response:

If the specified sensor is front USB connector, reset the front USB cable on the system board. If the

specified sensor is front video connector, reset the front video cable in the system board. If the specified sensor is
PwrPaddle cable, complete the following steps until problem is solved:

1.

Reseat the power paddle cable on the system board.

2.

Replace the power paddle cable.

3.

(Trained technician only) Replace the supercap n. (n = supercap number)

4.

(Trained technician only) Replace the system board.

Front Video :

806f011b-0c01ffff

The connector [PhysicalConnectorElementName] has encountered a configuration error. (FP

LCD Cable)

Explanation:

This message is for the use case when an implementation has detected an Interconnect Configuration

Error.

May also be shown as 806f011b0c01ffff or 0x806f011b0c01ffff

Severity:

Error

Alert Category:

Critical - Other

Serviceable:

Yes

CIM Information: Prefix:

PLAT and

ID:

0266

SNMP Trap ID:

50

Automatically notify Support:

Yes

User response:

1.

Check system event log is showing LCD cable sensor has deasserted.

2.

Reseat LCD cable on the system board.

3.

Reset LCD cable on LCD panel.

4.

Replace LCD cable.

806f011b-0701ffff • 806f011b-0c01ffff

472

System x3650 M5 Type 5462: Installation and Service Guide

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments