manualshive.com logo in svg

IBM System x3650 M5, Installation And Service Manual, Page: 550 / 1010

Share
Download
IBM System x3650 M5 Installation And Service Manual Download Page 550

806f0507-0302ffff

[ProcessorElementName] has a Configuration Mismatch. (CPU 2)

Explanation:

This message is for the use case when an implementation has detected a Processor Configuration

Mismatch has occurred.

May also be shown as 806f05070302ffff or 0x806f05070302ffff

Severity:

Error

Alert Category:

Critical - CPU

Serviceable:

Yes

CIM Information: Prefix:

PLAT and

ID:

0062

SNMP Trap ID:

40

Automatically notify Support:

No

User response:

1.

Check for a server firmware update. Important: Some cluster solutions require specific code levels or coordinated

code updates. If the device is part of a cluster solution, verify that the latest level of code is supported for the
cluster solution before you update the code.

2.

Make sure that the installed microprocessors are compatible with each other.

3.

(Trained technician only) Reseat microprocessor n.

4.

(Trained technician only) Replace microprocessor n. (n = microprocessor number)

806f0507-2584ffff

[ProcessorElementName] has a Configuration Mismatch. (All CPUs)

Explanation:

This message is for the use case when an implementation has detected a Processor Configuration

Mismatch has occurred.

May also be shown as 806f05072584ffff or 0x806f05072584ffff

Severity:

Error

Alert Category:

Critical - CPU

Serviceable:

Yes

CIM Information: Prefix:

PLAT and

ID:

0062

SNMP Trap ID:

40

Automatically notify Support:

No

User response:

1.

Check for a server firmware update. Important: Some cluster solutions require specific code levels or coordinated

code updates. If the device is part of a cluster solution, verify that the latest level of code is supported for the
cluster solution before you update the code.

2.

Make sure that the installed microprocessors are compatible with each other.

3.

(Trained technician only) Reseat microprocessor n.

4.

(Trained technician only) Replace microprocessor n. (n = microprocessor number)

806f0507-0302ffff • 806f0507-2584ffff

534

System x3650 M5 Type 5462: Installation and Service Guide

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments