manualshive.com logo in svg

IBM System x3650 M5, Installation And Service Manual, Page: 481 / 1010

Share
Download
IBM System x3650 M5 Installation And Service Manual Download Page 481

806f010d-0414ffff

The Drive [StorageVolumeElementName] has been disabled due to a detected fault. (Drive 20)

Explanation:

This message is for the use case when an implementation has detected a Drive was Disabled due to

fault.

May also be shown as 806f010d0414ffff or 0x806f010d0414ffff

Severity:

Error

Alert Category:

Critical - Hard Disk drive

Serviceable:

Yes

CIM Information: Prefix:

PLAT and

ID:

0164

SNMP Trap ID:

5

Automatically notify Support:

Yes

User response:

1.

Run the hard disk drive diagnostic test on drive n.

2.

Reseat the following components: a. Hard disk drive (wait 1 minute or more before reinstalling the drive) b.

Cable from the system board to the backplane

3.

Replace the following components one at a time, in the order shown, restarting the server each time: a. Hard

disk drive b. Cable from the system board to the backplane c. Hard disk drive backplane (n = hard disk drive
number)

806f010d-0415ffff

The Drive [StorageVolumeElementName] has been disabled due to a detected fault. (Drive 21)

Explanation:

This message is for the use case when an implementation has detected a Drive was Disabled due to

fault.

May also be shown as 806f010d0415ffff or 0x806f010d0415ffff

Severity:

Error

Alert Category:

Critical - Hard Disk drive

Serviceable:

Yes

CIM Information: Prefix:

PLAT and

ID:

0164

SNMP Trap ID:

5

Automatically notify Support:

Yes

User response:

1.

Run the hard disk drive diagnostic test on drive n.

2.

Reseat the following components: a. Hard disk drive (wait 1 minute or more before reinstalling the drive) b.

Cable from the system board to the backplane

3.

Replace the following components one at a time, in the order shown, restarting the server each time: a. Hard

disk drive b. Cable from the system board to the backplane c. Hard disk drive backplane (n = hard disk drive
number)

806f010d-0414ffff • 806f010d-0415ffff

Appendix A. Integrated management module II (IMM2) error messages

465

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments