IBM System x3650 M5 Installation And Service Manual Download Page 51

Page: 51 / 1010

– Type 6 PCI riser card

Riser-card assembly LEDs

The following illustration shows the light-emitting diodes (LEDs) on the PCI
riser-card assembly.

Note:

Error LEDs remain lit only while the server is connected to power.

PCI riser-card assembly

Slot 6, PCIe x8

Slot 8, PCIe x8

Slot 7, PCIe x8

Figure 33. Type 5 PCI riser card

PCI riser-card assembly

Slot 6, PCIe x16

Slot 8, PCIe x8

Figure 34. Type 6 PCI riser card

Upper PCI slot error LED

Center PCI slot error LED

Lower PCI slot error LED

Figure 35. Riser-card assembly LEDs

Chapter 1. The System x3650 M5 server

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M5

Reviews:

IBM System x3650 M5, Installation And Service Manual, Page: 51 / 1010

Search results

Summary of Contents for System x3650 M5

Reviews: