IBM System x3650 M5 Installation And Service Manual Download Page 151

Page: 151 / 1010

16x2.5-inch drive model

The internal routing for the 16x2.5-inch drive model cables.

The following illustration shows the internal routing for the 16x2.5-inch drive
model cables.

16x2.5-inch simple-swap hard disk drive model

16x2.5-inch simple-swap hard disk drive with hardware RAID

SAS signal cable

Power / configuration
cable

SAS 0 SAS 1

Figure 52. 8x2.5-inch hot-swap hard disk drive cabling

Chapter 5. Removing and replacing components

135

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M5

Reviews:

IBM System x3650 M5, Installation And Service Manual, Page: 151 / 1010

Search results

Summary of Contents for System x3650 M5

Reviews: