IBM System x3650 M5 Installation And Service Manual Download Page 332

Page: 332 / 1010

Table 16. Events that automatically notify Support (continued)

Event ID

Message String

Automatically
Notify
Support

806f050c-2018ffff

Memory Logging Limit Reached for
[PhysicalMemoryElementName] on
Subsystem [MemoryElementName]. (DIMM
24)

Yes

806f050c-2581ffff

Memory Logging Limit Reached for
[PhysicalMemoryElementName] on
Subsystem [MemoryElementName]. (All
DIMMS)

Yes

806f060d-0400ffff

Array [ComputerSystemElementName] has
failed. (Drive 0)

Yes

806f060d-0401ffff

Array [ComputerSystemElementName] has
failed. (Drive 1)

Yes

806f060d-0402ffff

Array [ComputerSystemElementName] has
failed. (Drive 2)

Yes

806f060d-0403ffff

Array [ComputerSystemElementName] has
failed. (Drive 3)

Yes

806f060d-0404ffff

Array [ComputerSystemElementName] has
failed. (Drive 4)

Yes

806f060d-0405ffff

Array [ComputerSystemElementName] has
failed. (Drive 5)

Yes

806f060d-0406ffff

Array [ComputerSystemElementName] has
failed. (Drive 6)

Yes

806f060d-0407ffff

Array [ComputerSystemElementName] has
failed. (Drive 7)

Yes

806f060d-0408ffff

Array [ComputerSystemElementName] has
failed. (Drive 8)

Yes

806f060d-0409ffff

Array [ComputerSystemElementName] has
failed. (Drive 9)

Yes

806f060d-040affff

Array [ComputerSystemElementName] has
failed. (Drive 10)

Yes

806f060d-040bffff

Array [ComputerSystemElementName] has
failed. (Drive 11)

Yes

806f060d-040cffff

Array [ComputerSystemElementName] has
failed. (Drive 12)

Yes

806f060d-040dffff

Array [ComputerSystemElementName] has
failed. (Drive 13)

Yes

806f060d-040effff

Array [ComputerSystemElementName] has
failed. (Drive 14)

Yes

806f060d-040fffff

Array [ComputerSystemElementName] has
failed. (Drive 15)

Yes

806f060d-0410ffff

Array [ComputerSystemElementName] has
failed. (Drive 16)

Yes

806f060d-0411ffff

Array [ComputerSystemElementName] has
failed. (Drive 17)

Yes

806f060d-0412ffff

Array [ComputerSystemElementName] has
failed. (Drive 18)

Yes

316

System x3650 M5 Type 5462: Installation and Service Guide

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M5

Reviews:

IBM System x3650 M5, Installation And Service Manual, Page: 332 / 1010

Search results

Summary of Contents for System x3650 M5

Reviews: