manualshive.com logo in svg

IBM System x3650 M5, Installation And Service Manual, Page: 250 / 1010

Share
Download
IBM System x3650 M5 Installation And Service Manual Download Page 250

5.

Remove the fan cage assembly (see “Removing the fan cage assembly” on
page 172).

6.

Insert the backplate assembly/backplane tabs into slots on the bottom of the
cage and push the backplate assembly/backplane forward into the release
latch (on top of the backplate assembly/backplane cage) until the backplate
assembly/backplane is locked in place.

Note:

You can connect the cables to the drive backplate assembly/backplane

before installing the backplate assembly/backplane onto the cage or you can
connect the cables after you install the backplate assembly/backplane, if that
is easier for you.

7.

Connect the SAS signal and power/configuration cables to the backplate
assembly/backplane and the system board. See 2.5-inch hard disk drive cable
connection for details.

8.

Replace the fan cage and fans if you removed them (see “Replacing the fan
cage assembly” on page 173 and “Replacing a hot-swap fan” on page 175).

9.

Reinstall the hard disk drives (see “Replacing a hot-swap hard disk drive” on
page 155).

10.

Install the top cover (see “Replacing the top cover” on page 147).

11.

Slide the server into the rack.

12.

Reconnect the power cords and any cables that you removed.

13.

Turn on the peripheral devices and the server.

2.5-inch HDD hot-swap backplane

2.5-inch HDD hot-swap
backplane (expander)

Figure 182. 2.5-inch simple-swap backplate assembly/hot-swap hard disk drive backplane
installation

234

System x3650 M5 Type 5462: Installation and Service Guide

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments