manualshive.com logo in svg

IBM System x3650 M5, Installation And Service Manual, Page: 161 / 1010

Share
Download
IBM System x3650 M5 Installation And Service Manual Download Page 161

Removing and replacing server components

This section provides information for removing and replacing components in the
server.

Removing and replacing structural parts

Replacement of structural parts is your responsibility. If IBM installs a structural
part at your request, you will be charged for the installation.

The illustrations in this document might differ slightly from your hardware.

SAS signal cable

Power / configuration
cables

SAS 0

SAS 1

Figure 67. 12x3.5-inch hot-swap hard disk drive cabling

Chapter 5. Removing and replacing components

145

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments