manualshive.com logo in svg

IBM System x3650 M5, Installation And Service Manual, Page: 835 / 1010

Share
Download
IBM System x3650 M5 Installation And Service Manual Download Page 835

I.1800C

[I.1800C]

Explanation:

A cache type mismatch has been detected for one or more processor packages. Processors have one or

more cache levels with mismatched type

Severity:

Error

User response:

Complete the following steps:

1.

Verify that matching processors are installed in the correct processor sockets. Correct any mismatch found.

2.

Check the IBM support site for an applicable service bulletin or firmware update that applies to this processor

error.

3.

(Trained technician only)Replace the system board

I.1800D

[I.1800D]

Explanation:

A cache associativity mismatch has been detected for one or more processor packages. Processors have

one or more cache levels with mismatched associativity

Severity:

Error

User response:

Complete the following steps:

1.

Verify that matching processors are installed in the correct processor sockets. Correct any mismatch found.

2.

Check the IBM support site for an applicable service bulletin or firmware update that applies to this processor

error.

3.

(Trained technician only)Replace the system board

I.1800E

[I.1800E]

Explanation:

A processor model mismatch has been detected for one or more processor packages. Processors have

mismatched Model Number

Severity:

Error

User response:

Complete the following steps:

1.

Verify that matching processors are installed in the correct processor sockets. Correct any mismatch found.

2.

Check the IBM support site for an applicable service bulletin or firmware update that applies to this Processor

error.

3.

(Trained technician only)Replace the system board

I.1800F

[I.1800F]

Explanation:

A processor family mismatch has been detected for one or more processor packages. Processors have

mismatched Family

Severity:

Error

User response:

Complete the following steps:

1.

Verify that matching processors are installed in the correct processor sockets. Correct any mismatch found.

2.

Check the IBM support site for an applicable service bulletin or firmware update that applies to this processor

error.

3.

(Trained technician only)Replace the system board

I.1800C • I.1800F

Appendix B. UEFI/POST diagnostic codes

819

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments