manualshive.com logo in svg

IBM System x3650 M5, Installation And Service Manual, Page: 314 / 1010

Share
Download
IBM System x3650 M5 Installation And Service Manual Download Page 314

5.

To obtain more working room, remove the fan cage (see “Removing the fan
cage assembly” on page 172).

6.

Pull the hard disk drives or fillers out of the server slightly to disengage them
from the backplanes. For more information, (see “Removing a hot-swap hard
disk drive” on page 154).

7.

Disconnect all cables from the system board and backplanes.

8.

Install the new backplane in slot 2 or slot 3 depending on your configuration.
Insert the backplane tabs into slots on the bottom of the cage and push the
backplane forward into the release latch (on top of the backplane cage) until
the backplane is locked in place.

Note:

You can connect the cables to the drive backplane before installing the

backplane onto the cage or you can connect the cables after you install the
backplane, if that is easier for you.

9.

Connect mini-SAS HD cables, power/configuration and Mini-SAS HD Y-cable
which come with the option kit to the backplanes and the system board.

4-drive filler panel

Figure 257. Filler panels

2.5-inch HDD hot-swap backplane

2.5-inch HDD hot-swap
backplane (expander)

Figure 258. Expander installation

298

System x3650 M5 Type 5462: Installation and Service Guide

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments